SailNet Community - Reply to Topic
Thread: Bristol 32- Deck Stepped Mast - Lighting Protection Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
06-26-2012 03:01 PM
Re: Bristol 32- Deck Stepped Mast - Lighting Protection

I just finished a repair that involved removing two 1 1/2 sea cocks in the head on my Bristol 32 with a deck stepped mast. The valves appeared to be bonded with wire but I noticed that not all the valves on the boat were. When I traced the wire it led from chainplates port and starboard, down to the valves. It looks like an attempt at lightning protection to me. otherwise, why connect the chainplates. I'm in Seattle where thunder storms are not common. They happen of course, but not like other parts of the country or even eastern Washington east of the Cascade mountains.

I disconnected the wire. The way I see it, there are better paths to ground in the marina than my boat if the big metal stick in the sky isn't connected to the water via wire and thru hulls. The wire wouldn't carry the charge very well anyway.

08-17-2011 08:49 AM
HDChopper "Lately with several nearby boats getting hit with heavy electronic damage, and fortunately nobody was hurt, I have gotten more concerned about our deck stepped mast"

There may be some valuable info in your opening statment did thay all have "protection" ? JMHO
08-16-2011 06:26 PM
kd3pc Many builders do not endorse the process you have been given for lightning protection, even today. There is not conclusive evidence that grounding the mast does anything. The only thing that the down cable to a bolt to a plate on the outside MAY do is direct the strike and blow a hole in the hull. You would be better to leave things as they are...

you might review the recent post:

lots of good info
08-16-2011 06:08 PM
FloridaWriter The first generation Bristols with deck stepped masts did not have any grounding wire from the mast to the keel. You could run a wire from the mast heel through the cabintop down to the keel easily enough.

Good luck with your project.
08-06-2011 06:06 PM
Bristol 32- Deck Stepped Mast - Lighting Protection

Lately with several nearby boats getting hit with heavy electronic damage, and fortunately nobody was hurt, I have gotten more concerned about our deck stepped mast.

A good friend of mine swears that the boat has to have a grounding strap in the construction somewhere, but I have not found it yet. Any suggestions? Perhaps someone knows a good source for construction information about this boat, since the yard in Bristol, RI has been converted to a yc/marina.

There is a cast aluminum deck plate with four or five bolts and an offset mahogany panel for the head to port and the locker to starboard. The door to the head has a 3" x 4" (approximate) mahogany post. I have not been able to find any signs of lightning protection straps, copper tubes, cables in this area under the cabin sole.

This also leads me to another question, our keel is fiberglass encapsulated, so how could they have used the keel as ground? I am hoping that these issues were worked out when they built the boat, but somehow I don't think they had the same standards for boat certification that they have now.

I've thought about running a protected #5-6 copper cable down from the step, to an new bronze thru hull bolt which clamps onto a new heavy copper plate (about 2 sf ft) that I would fiberglass to the outside of the hull.

Any constructive thoughts you might have would be appreciated.

Please, no flamers here

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome