SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Engines > Gas > Atomic 4 > Need Advice on Changing Stuffing Box hose
 Not a Member? 


Thread: Need Advice on Changing Stuffing Box hose Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
08-28-2011 05:12 AM
downeast450 Yup! OP, just a little heat and a few good taps all around, repeated several times over a few months whenever I am down there fussing with something. Then after haul out the socket / tension gets added to the mix.

Down
08-25-2011 07:50 PM
OPossumTX I prefer KROIL but PB Blaster is good too. A little heat helps but too much creates serious problems.
08-07-2011 12:38 PM
downeast450 Tom,

I am going to pull the shaft on my I-28 this winter. I need to replace the cutlass bearing and will replace the coupling hose at the same time. Knowing this is on the schedule I have been giving the shaft coupling a small dose of PB Blaster and a couple of "taps" with a ball peen hammer each time I am near by doing something else. I have been doing this for several months anticipating a problem getting it to come loose from the shaft when the time comes. I will schedule the actual removal for a bitterly cold part of the Maine winter and don't see a problem with warming the flange a little. My first choice, along with this preparation, will be to put tension on the joint with a socket that fits into the shaft end of the coupling and allows me to tighten the three bolts progressively. This will, in theory, push the shaft out of the coupling. I am not expecting this to happen quickly and plan to make a trip to the coupling bolts for another fractional turn each time I visit the boat. If it comes loose by the end of March I will consider it "on time and well done". I have always had good luck with blaster, "taps", heat and patience. That is how I got the 2 blade prop off this spring when I replaced that with the 3 blade Indego. That was a good decision, too.

Down
08-07-2011 10:49 AM
HPLou The following link to Compass Marine is an excellent source for many DYI boat repairs.


Re-Packing A Traditional Stuffing Box Photo Gallery by Compass Marine at pbase.com
08-07-2011 09:26 AM
wheelhouse Pirate Soul,

The hose used for stuffing boxes is significantly thicker than exhaust hose, use the right stuff.

My understanding is that one must pull the rudder in order to pull the shaft.

Of course the shaft flange must come off, that seems to be the biggest issue. Some force it off by placing a socket btwn the two halves & tightening. Others, pull the engine and cut the flange off of the shaft (cutting just the flange NOT THE SHAFT) & and replacing it with new one from Moyer. Been told that using heat was a definite no-no.

r,
cdw
07-19-2011 08:58 AM
Piratesoul
Need Advice on Changing Stuffing Box hose

I need tips, pointers, what not to do, on pulling out the prop shaft to replace the stuffing box hose on my A4.
Thank you, Tom

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 10:04 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.