|Topic Review (Newest First)|
|09-06-2011 01:48 PM|
I replaced the keelbolts on my Pearson 26 this past spring. I torqued the bolts to something near 80 ft-lbf. Dan Pfeiffer's P26 web page has all the details on the bolt size (3/8" - I think??) and torque for a P26.
Overtorqueing (is that a verb??) can damage the bits between the nut and bolt (i.e. fiberglass and any filler material), and serves no purpose other than to reduce the "additional" load capacity (i.e. load beyond the load created by torquing the bolt - like holding the keel in place).
|09-06-2011 12:12 AM|
|CharlieCobra||We did 300 Ft Lbs on 1 1/4" SS with anti seize on the keel we did. The bolts are rated to 500. This was after talking to the designer about it.|
|09-05-2011 11:23 PM|
Originally Posted by BELLATRIX1965 View Post
Actually, I used some specs that match up pretty well to the posted chart. I posed the question out of mere curiosity because I read & hear so many things like the "techniques" in my OP rather than anything technical or scientific - so unlike my other passion - cars. There everything is spec'd to the Ft/Lb.
|09-05-2011 11:06 PM|
It is possible to crush solid glass by over tightening keel bolts.
The link posted above is a good layman's guide
|09-05-2011 10:45 PM|
Yes, size DOES matter! And material type, and thread type (fine or coarse) - AND is it dry torque or wet torque? Dry torque is what it sounds like; wet torque refers to anti-sieze or oil applied to the threads AND under the head of the bolt or nut. Due to the reduced friction, a bolt torqued wet is under much more strain than the same bolt torqued dry.
If you can, I'd contact the manufacturer of your boat and get their recommendations.
|09-05-2011 06:10 PM|
Most every boat i have seen is SOLID glass in the keel bolt area except some older Catalinas that never got the upgrade
BUT i think most boats have a user group or info available someplace on the original torque level
|09-05-2011 05:30 PM|
|Faster||I think you also need some info as to what the hull/keel sump structure can take in terms of compression as you torque the bolts - so taking the data from the tables for the thread/size alone may not be the whole picture..|
|09-05-2011 02:45 PM|
Originally Posted by donradclife View Post
|09-05-2011 02:12 PM|
Steel Bolt Torque Specifications Table - Engineer's Handbook
|09-05-2011 02:05 PM|
Keel Bolt Torque
I have a question for the members - does anyone know any engineering rules that would allow calculating the torque required on a given keel bolt or bolts?
The reason I ask is that the general attitude seems to be "more is better", "crank on them until they squeal", or "put a pipe on a breaker bar and pull until the suckers scream for mercy". I've never seen anything much more technical or sophisticated than that.
I've always understood that a specific torque is required in order to stretch the bolts properly to achieve proper clamping force - this varies with the size of bolt, material it's made of etc.
Also, high torque is required to compensate for powerful, high frequency repetitive or rotational forces - engine cylinder heads, road wheels etc. not static loads where the bolts are only "locating" the parts in question.
To my eye, a keel falls somewhere in between these extremes - repetitive flexing forces from the boats motion but not really high frequency. Considering that such highly loaded fasteners like cylinder head bolts, connecting rod bolts, main bearing caps etc. are only torqued to values like 80 Ft/Lbs, I don't understand the need for keel bolts to be run up to 150 - 300 Ft/Lbs, especially considering they are generally stainless steel which I understand compares to, at best, a grade 3 fastener. It seems to me that these extreme torques are only going to crush the hull material, overstretch the bolt and/or risk galling the fasteners.