SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > LPG plumbing - teflon tape?
 Not a Member? 


Thread: LPG plumbing - teflon tape? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
11-01-2011 11:47 PM
funjohnson When I was switching over the LPG, I was given a tube of Permatex 2A gasket by the supplier of the new stove orifices.
11-01-2011 08:15 PM
deniseO30 Just a note about pipe threads, "NPT" The dope or tape helps fill microscopic gaps on the edges and valleys of the thread, NPT threads are tapered, the more you tighten the tighter they get, EXCEPT, you can go too far and stretch the receiving fitting, or split it (rare occurrence) If you have ever seen old dies cut threads (My dad was cheap sob plumber) the threads will be ragged, near impossible to seal, if you buy pipe nipples make sure the threads are smooth if they feel rough, don't use them.
11-01-2011 07:59 PM
JohnRPollard Hi Mark,

Sounds like a good project you've got going there -- nice upgrade!

The answer to your question depends in part on what kind of fittings you are using. Many of the connections now used in propane systems have flanges that are sealed by compression or o-rings. In those cases, it's not necessary to use tape or other.

If compression flanges or o-rings are absent, and it's just threads doing the connecting, I've had very good luck with standard teflon tape. Make sure to wrap it in the same direction that the threads will be turned in. Otherwise, it will bind up as you screw the two pieces together. Also, be careful to make sure the tape doesn't make a flap over the opening of the hose -- I once spent a few hours troubleshooting a lack of flow through only to discover the tape was blocking the orifice.

Remember to always pressure test the system after making these connections, and on a regular basis throughout the season. Good luck!
11-01-2011 04:45 PM
overbored 567 best stuff. good for years in the tube. I use it a lot. better then tape. can be undone. small tube is about $5 can be used for all plumbing on the boat even diesel.
11-01-2011 04:33 PM
hellosailor Mark, I think you'd be fine either way. With teflon tape ust don't wrap the very end of the thread, so no tape slivers get sliced off and go downstream into the regulator or jets. With LocTite, you probably have to degrease the threads for best results, and of course it actually has a shelf life--you'll throw out most of the bottle two(?) years from now, or it won't seal properly.

But either one will work.
11-01-2011 03:36 PM
MarkSF I looked at Loctite and they do 561 and 567, both are semi-setting compounds (can be dismantled again) that are claimed to replace tape and are approved for LPG use up to 150PSI. Should be fine for my low pressure side?

Has anyone used them?
11-01-2011 03:15 PM
zboss Use pipe dope for a permanent attachment and tape for semi-permanent.

Oh... also... if you use tape be sure to use the higher double thickness grade (yellow not white tape).
11-01-2011 01:33 PM
MarkSF
LPG plumbing - teflon tape?

The day is nearly here to re-commission the LPG system.

I have new tanks that aren't rusted out, a new Trident regulator with pressure gauges for leak checking, the locker has been painted inside with bilgekote, and I have a new solenoid valve / leak detector unit.

The valve will go in the locker just after the regulator, and the leak detector sensor will go in the bilge.

There's an existing pre-made hose to the locker which I'm going to re-use.

So all I need to do is fit the solenoid valve to the regulator, and the hose to the valve. Is teflon tape still the thing? I ask because I've heard of better liquid sealants that set.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 03:20 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.