|Topic Review (Newest First)|
|02-03-2012 10:39 PM|
Originally Posted by tap View Post
|02-03-2012 09:50 PM|
Originally Posted by SanDiegoChip View Post
|02-02-2012 11:48 PM|
Originally Posted by MarkSF View Post
Just to clarify..You can not do that and meet the ABYC standard.
Wire twisting, Western Union splices etc. do not count under ABYC E-11 as a "mechanical connection" to which you can then apply solder and call it a day....
|02-02-2012 11:25 PM|
Note that soldering is not forbidden by ABYC, just having no other form of strain relief on a soldered connection IS.
You can solder two wires together and then form a loop in the wire, and apply cable ties.
|02-02-2012 07:07 PM|
OK did the Air Breeze wind generator wiring from the #6 cables to the Air Breeze #10 wires.
The need for the #6 wires is because the wire run is over 30'.
The #6 connectors worked great for this.
Now to find my darn heat gun!
Heat shrink needs to be moved into place and shrunk.
#10 to #6
Shrink the heat shrink and it is ready to mount!
Thanks for all the imput.
|02-01-2012 02:07 PM|
OK, yes I had read some reviews about the Harbor Freight tool and die sizes. It does do a nice crimp and on a 2/0 size was the only one we could really afford. As we use it rarely and it does a nice crimp it seems OK.
I do release that our anchor windlass is a critical system and checked the crimp out and it was great.
This die says 8 AWG and that would mean electrical wire would it not, or is cable sized the same?
The Air Breeze is not critical and this crimp is solid. It beats hitting it with a hammer and the tools shown do not seem to go up in size to #6.
We usually order our cables from GenuineDealz.com - Marine Electrical, Boat Wire & Cable, Custom Battery Cables and have them do the crimp. In this case we cannot have them do the crimping.
I will hate it if the anchor windlass crimp fails for some reason. We will keep an eye on it. We have a few crimps to make on our solar controller as the cables #4 need to be cut for a fuse and a fuse block.
That should be the end of the crimping we need to do. We were not planning on taking this tool cruising, 9 moths from now. May re-think that or get another one?
Whay would these crimps fail?
|02-01-2012 01:22 PM|
Tested crimping tool
Ok once again I was mistaken. The wires we need to use are #6 not #8
We did some testing with our Harbor Freight hydraulic crimping tool. We first bought it for one job. That was to crimp 2/0 cables from our windlass to batteries after we did a refit of the cables. We had to use the 00 dies in the tool to make that crimp. So we figured the dies would be different for the #6 cables but now we think not.
The wires #6 red\black
OK the stripping was not so great as I busted some strands but we did not have much to work with on that tool.
We tried the #6 dies in the tool and the crimp looks real good and it can not be torn apart, at least by me. We tried the #8 dies but it crimp looks too flat (right).
We used #6 cable and #6 butt connectors.
We also tried two #10 wires together into one # 6 but connector and they fit real nice. We did not do a crimp, seemed a waste of a connector.
We also tried a #10 wire bent over in two and it fit real nice in the #6 butt connector.
We will need to wire the green (ground) and white (neutral) wires together at the Air Breeze so that was one test.
We will need to wire a #10 black wire from the Air Breeze wind generator to the #6 black to battery negative so that was another test.
We also need to wire in a switch and a 5/16 battery eye to fuse terminal.
Need to purchase more # 6 terminal ends and some heat shrink with glue.
So it looks like this all works out. Now to do the job!
|01-31-2012 10:45 PM|
You know, I've always wondered about those cutaways. Sure, it LOOKS like the copper strands have been smoothly and uniformly compressed. But is that from the crimp, or from the action of the saw or cutoff wheel, neatly smoothing and polishing them?
The closer we look, the more error we create?
|01-31-2012 06:27 PM|
Originally Posted by hellosailor View Post
An oval heat shrink crimp die did this..
And this is a cut away of a crimp made by my $1200.00 AMP aerospace certified crimp tool. Looks oval to me...
|01-31-2012 05:41 PM|
Maine, since when does a plain oval shape die count as a proper crimp for anything?
Chip, is it at all feasible to simply remove the thinner wire from the airgen, and run the 8AWG cable all the way into it? That also eliminates the need to splice completely.
The HF tool may be the only one of its kind on the market and it sure LOOKS good, but if you find the thread discussing it...there's some question of exactly wtf they are selling and apparently even that varies from lot to lot.
Of course, folks have been known to simply use a vise and "swage" the hell out of battery lugs when there's no fancy $200 crimping tool around.
|This thread has more than 10 replies. Click here to review the whole thread.|