SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > On Board > Gear & Maintenance > Roller furling jib on a trailerable?
 Not a Member? 


Thread: Roller furling jib on a trailerable? Reply to Thread
Title:
  

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


Topic Review (Newest First)
02-19-2012 10:04 AM
PBzeer The H 26 I had came with the CDI furler. At the end of the season before hauling the boat out of the water, I would remove the sail,while leaving the furler attached. After securing the mast and furler, I would put a couple of heavy large ziploc bags over the drum and then tape them across the opening.
02-19-2012 09:10 AM
H and E I have a Catalina 25 on a trailer with roller furler and Genoa 150. I use an A frame to step the mast and have a crutch in the stern with a roller. I can raise/lower with cockpit winch by myself. Roller on crutch allows me to disconnect the mast at the step and walk it forward to store for travel. I use the halyards to wrap the rolled sail to the mast. A frame and crutch are easily stored in the salon or truck bed.
02-19-2012 02:42 AM
MarkSF
Quote:
Originally Posted by nccouple View Post
Any trailerable sailors using a roller furling jib? Seems to be an easy and inexpensive set up. However the complications of raising and lowering the mast seem to be the issue. Would love to hear how you overcome this. Thanks.
I added one to my Wayfarer. I used the Harken small boat furler which has no foil, it just uses the wire luff of the jib. You need a jib with the luff wire stitched in. Raising and lowering the mast was easy as the jib halyard was internal to the mast, and came out of the mast inside the boat. Therefore all you had to do was stand in the boat, raise the mast, then pull on the jib halyard and cleat it off.

The Wayfarer was designed for 'shooting" bridges, where you need an easily lowerable and raisable mast. You were supposed to be able to sail towards a bridge, drop the mast at the last second, pass under the bridge, then put it up, all from the cockpit while steering. I never tried this!

When towing I would lash the jib & furler to the mast.
02-18-2012 10:38 PM
Izzy1414 nc,

I have have roller furled genoa with extrusion (CDI FF2) on my 26 foot trailer sailor. Stepping and unstepping the mast is not a problem. You just have to control the unattached drum end of the forestay during the process. I simply use the furler control line pulling forward to keep the end from flopping around. And as Kermie says, lash it to the mast when it's down.
02-18-2012 09:06 PM
CaptKermie There must be thousands of MacGregor owners out there with furlers on their trailerable boats and they all do it with ease, including myself. Google MacGregor 26 and you should find a few blogs. Try this one.
MacGregorSailors.com • Index page
You can bungie the furler to the mast easy enough for trailering or use a length of PVC extrusion to cradle the section of furler that extends off the bow with mast down. It is not all that difficult really.
02-18-2012 08:26 PM
BarryL Hey

My Catalina 22 came with a roller furled. I would leave the sail on an rolled up. No problems stepping and unwrapping the mast with the sail on

Barry
02-18-2012 08:20 PM
Lake Superior Sailor Could use old style furler without extrusions..Dale
02-18-2012 07:33 PM
nccouple
Roller furling jib on a trailerable?

Any trailerable sailors using a roller furling jib? Seems to be an easy and inexpensive set up. However the complications of raising and lowering the mast seem to be the issue. Would love to hear how you overcome this. Thanks.

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


All times are GMT -4. The time now is 05:29 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.