SailNet Community - Reply to Topic
Thread: Grounding, bonding,AC, DC Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
07-10-2012 01:13 PM
Re: Grounding, bonding,AC, DC

The mast is stepped on the keel. I'm pretty sure it is grounded. I check when I get back to the boat. should I daisy chain everything back to the backing plate?
07-10-2012 10:25 AM
Re: Grounding, bonding,AC, DC

Wow, opinions vary on this subject. Let me begin by saying that I have been struck by lightning while underway and although electric/electronics were toasted crispy, hull integrity was fine.

Chainplates should be grounded although in point of fact an aluminum mast is the preferred down conductor, being a much better conductor than stainless steel stays. This is the path lightning will try and take and this is where boat lightning protection should be.

Recent information from the lightning capital of the USA. University of Florida

"......If the mast base is on top of the cabin, a downconductor is needed to connect the mast base to the ground strips. Use at least #4 gauge copper with preferably bimetallic copper/stainless connections to prevent galvanic corrosion.

Alternatively, make a strong mechanical connection and additionally braze or solder, to improve the electrical contact and lessen the chance of contact corrosion, then paint with an insulating coating. A keel-stepped mast similarly needs to be connected to the keelbolts with at least #4 gauge copper...."
07-10-2012 09:54 AM
Grounding, bonding,AC, DC

Grounding, bonding, AC neutral and green wire ground, and DC minus.

On my 1976 gulfstar I just replaced all my thru hulls and seacocks. *When I was taking them apart I noticed that the chain plates were tied to the seacocks and the seacocks were tied to the backing plate for my cutlass bearing. *All these were daisy-chained from bow to stern.

*I don't understand bringing the energy from a lightning strike down to a thruhulls? I would think you would want to run the lightning protection directly to the backing plate.

*The DC minus was tied to the engine block and the AC green wire ground and neutral went back to shore power. I believe these are correct.

All the bonding wires were either *broken or disconnected or corroded. These I'm pulling out and replacing with new. *I'm also going to replace the backing plate with a 3/8 bronze plate. *And I'm redoing my DC primary wiring.

I pretty well understand how most of this should be except for the chain plates/seacocks. *The chain plate wire is for lightning protection? *The seacocks wire is bonding for stray currents. *Should these two be tied together? * Can I run all these wires to a terminal block, and then a single wire to the backing plate? *Or should the lightning and bonding be run separate to the plate?

Also what size wire should I be using?
I understand that the AC and DC should never be tied together.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome