SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > General Interest > General Discussion (sailing related) > rigging question
 Not a Member? 

Thread: rigging question Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
08-15-2012 12:18 AM
Re: rigging question

Actually no it dosnt have any the shrouds just attach to the chain plate with a shackle. I knew it was missing something should it have a turn buckle on the forestay also. Thanks for all the info I just want to make this rig right
08-14-2012 09:13 PM
Re: rigging question

Sorry! Yes shrouds = stays!

You should have turnbuckles or something don't you? I am not familiar with your particular boat but it would be very unusual for a sail boat to have no means of adjusting stay tension. Perhaps if you have some pics?
08-14-2012 12:49 PM
Re: rigging question

When you say shrouds is that what I'm calling stays just checking cause I'm not real sure and how can I pre set the tension on them and get them close to right
08-14-2012 12:14 AM
Re: rigging question

Typically your upper shouds should be tight enough so that under load the leeward shroud goes a bit slack but not floppy when the rig is loaded up.( A rigger friend of mine said they should go just loose enough that you could pull the pin out.) The lowers are less critical but using the same rule will ensure that the mast stays in column under load.
08-13-2012 11:26 PM
Re: rigging question

Yes that's exactly what it is. I'm a machinist by trade so I'll have no problem tapping the mast base. The boat is a 19.5 ft Newport holiday. When we had a load on the rig we had three grown men sitting on the high side and sailing close hauled the stay lines on the starboard and the port sides one was tight and one was very loose because of the load is this OK or do I need yo work on this also. Any help appreciated thanks. ( excuse my lack of sailing terms haven't had time to learn them all yet).
08-13-2012 09:46 PM
Re: rigging question

Pics would help, but it sounds like you might be refering to rivets that hold the mast base that sleeves inside the mast section. If that is the case then the rivets should not be bearing any load. The rig tension should create enough compression to keep the mast firmly planted to the deck. If they sheared off it could be a result of ecessive rake or the mast leaning to leeward and trying to "slip off" the base which is presumably pinned to the deck at its pivot point.
Of course this is just speculation based on my experience with my last trailerable boat.
On my boat i drilled out the rivets, and then tapped the holes for machine screws. Through bolting is not necessary.
08-13-2012 08:42 PM
Re: rigging question

What year is the boat? what type of rivets? I would thru bolt it if possible or replace rivets with larger ones to ensure they dont fail underway. Pictures would help.
08-13-2012 08:28 PM
rigging question

Hey guys I'm new to sailing got a 20 ft Newport holiday. the older gentleman I got it from never pushed the boat. this last weekend me and some buddies did push it when we were done I took down the mast and noticed I had broke the pop rivets on one side of the mast base. what would cause this and how can I keep it from happening again. We only had 15 to 20 knot winds.

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 07:20 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.