SailNet Community - Reply to Topic
Thread: caulking hull planks on a Wooden Boat Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below


  Topic Review (Newest First)
08-16-2012 08:57 AM
Chrisper54
Re: caulking hull planks on a Wooden Boat

Thank you all for your great suggestions - I will pass them on to the captain/owner.
08-15-2012 06:32 PM
klem
Re: caulking hull planks on a Wooden Boat

What boat are you working aboard?

The preferred method for all of the schooners that I used to work with was to use cotton first, then oakum. On the hull, putty was dyed and then put into the seams after that. On deck, we poured hot pitch into the seams and then scraped the excess when it had cooled.

If things are coming out, you either used something inappropriate, the boat is working, or the caulking was not driven down deep enough in the first place.
08-15-2012 03:45 PM
oysterman23 In the sixties here on the east coast three strand oakum or...cotton sealed more often than not with boatlife in tube seam compound ....it was messy low paid work that actually required skill and one or two good teachers a long the way...Had to "feel" how much to twist the cotton and set it just enough with the caulking iron.....forgive me but red lead was old school then far outclassed by Boatlife Early Sikaflex or several other varieties...
If your cotton or oakum is all stringing out very likely it was not applied well or sealed properly afterwards....best to get someone experienced there to evaluate and guide the work.
Good luck
08-15-2012 02:54 PM
captflood
Re: caulking hull planks on a Wooden Boat

GREETINGS EARTHLINGS; -The old way was with White Lead and cotton string so any of the modern sealents that will addhear to the understrate and the wood is good beeing from Blighty I do not know what is available on your side of the pond . Lay six inches of the cauking then over-lab by three extend six then over lap again _-_-_-_-_-_ (I must spend more time finding out how to use this computer thingy ma bob) AS ALWAYS GO SAFE !
08-15-2012 01:07 PM
WanderingStar
Re: caulking hull planks on a Wooden Boat

+1 for Woodenboat, though you'll get conflicting advice there. Slickseam is great, but for use below water. Above water use seam compound, try interlux.
08-15-2012 12:43 PM
peterchech
Re: caulking hull planks on a Wooden Boat

Try forum.woodenboat.com they are pretty good with this kind of stuff
08-15-2012 07:50 AM
kd3pc
Re: caulking hull planks on a Wooden Boat

the caulking needs to be done while the boat is dry....hauled out....

hammer in the oakem, and as the wood swells with water, things tighten up nicely...
putting other things in or on the oakem, except for red lead is asking for trouble as most will prevent anything from sticking to the planking.

If the planking is oily, you may need to "prime" the joint with and oil based paint,

best of luck.
08-15-2012 04:12 AM
sea_hunter Slick Seam
08-15-2012 02:37 AM
Chrisper54
caulking hull planks on a Wooden Boat

I have the pleasure of working aboard a 77 foot wooden schooner. It appears that the sealing for the calking put in last spring is coming off. Does anyone have experience with this and a recommendation for a substance to top the oakem in a traditional wooden ship?

Please respond with experise that works

Chrisper

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

 
For the best viewing experience please update your browser to Google Chrome