SailNet Community - Reply to Topic
Thread: Centerboard damage. Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

  Topic Review (Newest First)
11-13-2012 09:24 AM
Re: Centerboard damage.

I'd open it up to see whats going on further down the CB. After you see what's going on, you can assess what should be replaced and how to do it. None-the-less, I concur that it shouldn't be that big of a job.
11-12-2012 09:14 PM
Re: Centerboard damage.

Herlihy's suggestion sounds reasonable. After cleaning out all the loose stuff and letting everything dry out (perhaps giving it some help with hot air) it shouldn't be too difficult to refill with goop and and re-glass the joint while holding the two sides in place. Material may cost less than $100, add a couple of hours of work, and you'll be back in business. Be sure to grease things while they're accessible.
11-12-2012 06:37 PM
Re: Centerboard damage.

Perhaps there was some other stuff in there eherlihy, but I didn’t see any evidence of it, just bits of resin. The rudder bearing was cast out of pure resin also. I noticed it crumbling at haul out last year and made a new bearing out of Delrin pre-launch this year.

The boat is a 1980 Irwin Citation 39. Only 600 made, and at last check 400 still floating. There is only one boat like mine, that I know of, here on the lakes. Almost half of the floaters are across the pond. Not much chance of finding a replacement.

The guy working on the board is well known in the local race community. He comes highly recommended. Said it wouldn’t be huge repair bill, and didn’t seem to think it was as bad as it looked. We’ll wait for the estimate before committing, but that is a much larger glass job than I am comfortable doing. Something I’d rather have done by a pro.
11-11-2012 10:10 PM
Re: Centerboard damage.

I don't know, but I suspect that the "rocks and mud" may have been ballast. It is not uncommon for manufacturers to use iron and cement encased in resin as ballast. It seems like water may have crept in there and between freeze/thaw and the formation of iron oxide, it broke the ballast into bite size pieces.
11-11-2012 08:54 PM
Re: Centerboard damage.

That is some major delamination going on with your CB.

Be prepared to pay through the nose if your 'yard' does the work for you. Labor rates of $80+/hr are not that unusual.

It might help to know what sailboat the CB is from and your general location (I assume lake, maybe Great Lake?). If you put your boat and location in your signature and profile I wouldn't be asking you these questions.

It is worth looking for used CBs for your boat on CL, Ebay or whatever, but not too likely you'd find a drop-in replacement.

If you are up for doing the work yourself then you could likely make a better than new replacement at home over the winter. Materials should cost well under $500, depending on how you do it.

Good luck with that board!
11-11-2012 07:42 PM
Centerboard damage.

Wed been having issues raising and lowering the CB. Towards the end of this season things got markedly worse. Thought Id have the folks at the marina drop it at haul out and see what gives. Looks like a lot gave.

Before we pulled the pin, with the CB about down, I grabbed the leading and aft edges and, without much effort, was able to move it laterally about a foot in each direction and twist it near the same amount. Little wonder we were having problems, not to mention just being slow. All kinds of lift and drag issues there, methinks.

Before haul out, my thought was to drop the board and toss it in the back of my truck. After seeing it I told them to keep it and give me an estimate. Its beyond my feeble skills to repair.

What looks like rocks and mud in there is broken up resin with a dash of lake scum for seasoning. Lucky for us it didnt rip clean out of there, wasnt much left holding things together. It would have been one wild ride if it had; the control cable and line are in remarkably good condition.

Weve never hit anything or run aground, but there is damage on the leading edge (we are the third owners). Figure that water got in there and the freeze/thaw cycle here on the lakes took its toll.

Not asking for any help here. Everyone has a morbid fascination when it comes to seeing damage, as long as it isnt theirs.

Just thought Id share.


Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

For the best viewing experience please update your browser to Google Chrome