SailNet Community - Reply to Topic

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > Boat Builders Row > Cal > Cal 2-27 spreader failure and mast bend
 Not a Member? 

Thread: Cal 2-27 spreader failure and mast bend Reply to Thread

By choosing to post the reply below you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Additional Options
Miscellaneous Options

Click here to view the posting rules you are bound to when clicking the
'Submit Reply' button below

Topic Review (Newest First)
02-10-2013 08:27 PM
Re: Cal 2-27 spreader failure and mast bend

Points well taken. I will be using for day sailing, weekending and short cruising on the Chesapeake Bay, generally favorable winds conditions year round. I read where the 2-27's have a known design flaw with undersized standing rigging and de-mastings, and all the wires should be increased by 1 size, so hopefully the owner was aware of this and did so when re-rigging. And the orig. wood spreaders have also been replaced-another plus.

From what I've read these older Cals were built conservatively and that may also apply to the mast.
I'm going to look at this boat as well as a 2-29, and they both have some potential issues to pay attention to, and the info readily available thru this forum's posts and other online sites have been very helpful.

Appreciate your input-
Cheers, Rob
02-10-2013 08:15 PM
Re: Cal 2-27 spreader failure and mast bend

Good points...and I could also see what the yard remembers about the extent of bend and repair necessary to get it fixed.
Thanks for chiming in.
02-10-2013 06:47 PM
Re: Cal 2-27 spreader failure and mast bend


To some extent it depends on what you hope to get out of the boat. A bent then fixed mast will always be less stiff than a new one as a function of the damage done to the underlying metal. However, if this is going to be a daysailor/weekender then I probably isn't a real concern, the damage is unlikely to be so severe than moderate weather and loads will cause problems.

If you want to seriously race the boat then the lack of stiffness, particularly the asymetric loss can be a big problem (this is why my J-22 has 2 masts a cruising and racing one). It can cause your sails to set slightly differently on different tacks, and will make mast failure more likely in lesser wind speeds.
02-10-2013 06:03 PM
Re: Cal 2-27 spreader failure and mast bend

I'd consider the boat...if the mast has no bend when out of the boat, or un-tensioned and there is no apparent damage such as a dimple or crease, I would expect you are no worse off than when looking at any other boat with a 45 year old rig.
02-10-2013 05:53 PM
Cal 2-27 spreader failure and mast bend

I called an owner about his 1977 Cal 2-27 that he is going to donate or sell for a low prive to get rid of the boar due to lack of use. He said that 2 years ago the original wood stbd spreader failed while sailing. The mast bent slightly, not sure where exactly, and after his insurance company surveyed the damage he had the mast straightened by a professional boatyard, both spreaders replaced with aluminum type and all standing rigging replaced(not sure if from Seals Spars & Rigging).

Even if I were to purchase the boat for a extreme minimal investment, is it worth the risk of future potential mast failure? Is there any testing procedure to evaluate the weakening of the mast due to what I would guess was the excessive tension caused by the opposite side upper shroud?

Before I decide to even look at the boat I'd appreciate any comments/advice from the rigging experts out there.

Thanks, Rob

Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

All times are GMT -4. The time now is 08:32 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.