Crealock 37 Yawl - SailNet Community
 
LinkBack Thread Tools
post #1 of 4 Old 09-10-2007 Thread Starter
Junior Member
 
Join Date: Jan 2007
Location: Kemah, TX
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
 
Crealock 37 Yawl

Does anyone know about this boat or ones like it? It's the Crealock 37 Yawl Cutter shown on Yacht World. It has a Volvo Penta MD11C saildrive. A friend has made an offer on the boat and I told him I would move it to Houston for him. Wanted to check if anyone knew about the boat history, etc.
tayana48cc is offline  
Quote Quick Reply Share with Facebook
Sponsored Links
Advertisement
 
post #2 of 4 Old 09-10-2007
Senior Member
 
teshannon's Avatar
 
Join Date: Aug 2006
Location: Philadelphia
Posts: 2,713
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 11
     
Don't know anything about it but love your boat!
teshannon is offline  
Quote Quick Reply Share with Facebook
post #3 of 4 Old 09-10-2007
Moderator
 
JohnRPollard's Avatar
 
Join Date: Mar 2007
Location: Chesapeake
Posts: 5,680
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 10
     
Are you referring to the 1977 model located in Ft. Lauderdale?

If so, that is a Crealock 37 yawl, as you point out. But it is not a Pacific Seacraft. It appears to be one of the original Crealock 37s that was built by Cruising Consultants (CC). When CC shut down (after building a couple dozen, I think), Pacific Seacraft acquired the moulds and built these boats for almost 30 years. Not many of the PSC boats were yawls (most were cutter or sloop rigged). The interior of this boat appears to have been built up entirely from wood, where as most of the PSC boats had a fibreglass pan (early on PSC sold some hulls/decks as kits, both with and without the pan). The portlights are different from those used by PSC too. And PSC did not use the saildrive engine arrangement (they put the prop in a skeg aperture and went with a conventional shaft).

The design has received many accolades and has a reputation for solid seaworthiness -- but I don't know much about the build quality of the CC boats.
JohnRPollard is offline  
Quote Quick Reply Share with Facebook
post #4 of 4 Old 09-14-2007
Junior Member
 
Join Date: Mar 2002
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
 
Yawl came from houston - might come back?

That boat was from Houston - sat for a long time because of sail drive issues - ( I understand that it has been resolved) be very careful on your inspection - I had talked to Crealock, interestingly enough he desighed it with a saildrive in mind AND tiller. CC hulls were usually fiinished by Westery in Costa Mesa, some of the old timers may still be there. You should get teh hhull number and call.

Still be careful on checking out the saildrive with electrical isolation - find someone (not necessarly a surveyor) to check it out for you.


Good luck

MKP
tranmkp is offline  
Quote Quick Reply Share with Facebook
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.


User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
Sloop, Cutter or Ketch jsgsail Boat Review and Purchase Forum 17 12-26-2008 02:47 PM
New to Sailing, please Help =) xyris Learning to Sail 19 11-17-2008 08:30 AM
My First Boat...Boat Term Question... Kacper General Discussion (sailing related) 38 09-23-2008 06:52 PM
Ketch/Yawl Handling svsymphony Seamanship & Navigation 19 07-05-2008 01:19 AM
diffrent rigs? (schooner, ketch, cutter, sloop) jbarros Boat Review and Purchase Forum 2 07-09-2003 04:10 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome