S2 9.2c haulout - SailNet Community

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Boat Builders Row > S2
 Not a Member? 


Reply
 
LinkBack Thread Tools
  #1  
Old 07-07-2009
Junior Member
 
Join Date: Jun 2008
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
kiminpr is on a distinguished road
S2 9.2c haulout

Okay! I am about to haul my S2 9.2C for the first time in a couple of weeks for bottom paint. I've read somewhere that because of the encapsulated keel the whole bottom of the keel must be supported - not just a couple of points - can anyone confirm this? I also want to replace the main halyard - is this easy? Are there any tricks? Please - advice - I'm a rookie! Thanks
Reply With Quote Quick reply to this message Share with Facebook
  #2  
Old 07-08-2009
Gary M's Avatar
Senior Member
 
Join Date: May 2006
Location: Sarnia ON
Posts: 673
Thanks: 3
Thanked 3 Times in 3 Posts
Rep Power: 9
Gary M is on a distinguished road
I have an S2 9.1 which is not the same vessel but built at the same time in the same shed. I seriously doubt that you have an encapsulated keel. Even if you did it would not be an issue. I assume you are getting lifted by two slings like everyone else so you need to get one sling in front of the keel and the other behind but positioned so you do not hit the shaft and strut.

Replacing the main halyard is not difficult. You likely have a rope to wire halyard if it is original, and you will likely go to an all rope halyard. You will have to attached a light line to the tail of your existing halyard and pull the old halyard down to the fore deck until it is replaced by the light line.

Then you attached the tail of the new halyard to the light line at the fore deck and pull the new halyard up to the top of the mast then down the mast and out the exit point. You really should go up the mast if it is not down and check that the sheave that the halyard runs through has not been chewed up by the wire. That will damage your nice new halyard.

good luck.

Gary
Reply With Quote Quick reply to this message Share with Facebook
  #3  
Old 07-08-2009
Junior Member
 
Join Date: Jun 2008
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
kiminpr is on a distinguished road
Great! Thanks so much for the advice -I think there is probably an all robe halyard there now. I'm not actually sure the keel is an encapsulated keel - someone called it that once. There are no keel bolts - just a fiberglass form with lead poured into it so it is an integral part of the hull. Well, thanks again
Reply With Quote Quick reply to this message Share with Facebook
  #4  
Old 07-10-2009
FishFinder's Avatar
Senior Member
 
Join Date: Feb 2008
Posts: 139
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 7
FishFinder is on a distinguished road
You do have an encapsulated keel, that is how mine is on 9.2A (same hull). My surveyor said to make sure the keel is supported back and front when blocked (set down in the yard). I believe the bulk of the weight and structure is in the forward part of the keel. When the boat is out of the water you can tap on the keel and tell that the front is more solid than the back part.

I replaced my halyard (and all my lines up the mast) by doing basically what Gary said ... tied line (I used cheap green fishing net line) to old halyard with say 3 half-hitches spaced about 3" apart. Then wrapped the whole deal with electrical tape so it would feed smoother through the sheaves. Got old line down, tied off the fishing net line. When I bought new line, attached it to fishing net line in the same way w/ half hitches and tape, then fed through. Be careful, DON'T PULL TOO HARD when feeding the line or you might pull all the half-hitches off and then you have to climb the mast.
__________________
1980 S2 9.2A (30') in Anacortes, WA
Aux power 13hp Volvo MD7A
Reply With Quote Quick reply to this message Share with Facebook
  #5  
Old 07-14-2009
Junior Member
 
Join Date: Jun 2008
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
kiminpr is on a distinguished road
Switching to a 3-blade prop?

Hey Thanks for all of our help - being that you two are familiar with S2's like mine, I am wondering about your thoughts on a three bladed prop. I have the original 13 hp engine - it's in very good shape, but only pushes the boat along at about 4.5 knots, which means really slow when heading into a current of 1.5 knots, and really has very little control backing up. would a three bladed prop help with this?
Reply With Quote Quick reply to this message Share with Facebook
Reply

Quick Reply
Message:
Options

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

 
Posting Rules
You may post new threads
You may post replies
You may post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Any ideas for haulout near Annapolis? saltypat Gear & Maintenance 8 08-26-2011 06:31 PM
Haulout on Pamlico stoutwench Gear & Maintenance 0 08-09-2006 12:37 PM
My First Haulout Dan Dickison Her Sailnet Articles 0 04-04-2002 08:00 PM
Surviving the Haulout Mark Matthews Gear and Maintenance Articles 0 02-15-2002 08:00 PM


All times are GMT -4. The time now is 11:06 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.