Inside the Asymmetrical Spinnaker - SailNet Community
  • 1 Post By administrator
LinkBack Thread Tools
post #1 of 3 Old 10-09-2006 Thread Starter
administrator's Avatar
Join Date: Jan 2000
Location: maryland
Posts: 1,887
Thanks: 3
Thanked 20 Times in 12 Posts
Rep Power: 10
Inside the Asymmetrical Spinnaker


Inside the Asymmetrical Spinnaker
by Sandy Goodall

Asymmetrical spinnakers (or aspins) have become so popular in the last few years that most sailors are aware of what they are and how to use them. But there are many versions of these sails, and sailmakers are constantly experimenting with different shapes and sizes in cruising and racing aspins-for all-around use or for sailing in very specific conditions.

It would be difficult, if not impossible, to get much of a consensus from competing sailmakers, regarding the "best" or "correct" size or shape for this type of sail. However, here are some of the things that I have discovered by designing and using aspins on a wide variety of racing and cruising boats over the last several years.

One of the biggest attractions with aspins is that because of their simplicity, they require less gear and fewer crew to handle than symmetrical kites, and that makes us more likely to use them more often. They make downwind sailing much more enjoyable, not to mention faster, and are extremely versatile sails in terms of achievable angles.

Some of the early predecessors to modern aspins were simply large, deep, lightly built (nylon) headsails, hanked to the forestay. These "fat drifters" were able to pull a boat off the wind surprisingly well, and because they were so easy to set and use, they were popular, particularly with cruising sailors. Slowly, the concept evolved, and once the luff was released from the forestay, the sail became a true "flying" sail-a spinnaker rather than a headsail.

Then came the search for a more effective size and shape. The best size and shape has a lot to do with the intended use. Racing boats will have several different aspins, of different sizes, shapes and materials, for different wind angles and wind speeds. But for all-around use, I think many sailmakers would now agree that a good all purpose aspin will have a luff length that is as long as possible, without the sail dragging in the water when it is hanging straight down in no wind.

Foot length has been, and still is, a topic for debate. Many sailmakers have marketed an all-around aspin design where the foot was approximately 160% of the boat's J measurement. I have found that with a modern (somewhat flatter) cross section shape, these sails work very well with a foot length of 180% of the J, just like the traditional symmetrical kites. Wider seems to want to collapse in light airs, while narrower can feel a bit underpowered.

Girth at half height also varies greatly. Aspins for racing One Designs, or where the aspin must replace a dedicated running symmetrical, often have a midgirth that is significantly larger than the foot girth. But the resulting shape has definite limitations regarding how "hot" you can reach. The fact is, the more midgirth you are trying to fly, the more camber (depth) is required to support those shoulders, so a "wide" sail usually becomes a "full" sail.

For best all-around performance, without having a whole quiver of different shapes and sizes to draw from, I have found that an aspin with max luff, foot length of 180% of J, and a midgirth of the same width as the foot, or just slightly narrower than the foot, works surprisingly well. At first glance, such a sail might seem a bit narrow at the midgirth, but this means that the sail is not carrying such large "shoulders" that it needs to be full. Under closer reaching angles, the sail can be trimmed with a tighter, straighter luff and the cross section shape will flatten accordingly. I am always amazed at how high these sails can be carried effectively, and yet still project out to weather when running deeper angles.

Clew height is another variable. As the sail is eased, the leech tension is reduced and the sail leech twists away to leeward. A good way to effectively retain some "downward" pull on the leech is to have the clew cut fairly high--typically at or near boom height.

Combine these basic parameters with a nicely rounded entry and a fairly flat exit, and you have a sail that can be trimmed through a surprisingly wide range of flying shapes, depending on the angle you are trying to sail. Tack height, luff tension, sheet tension and twist all have a significant effect on the resulting flying shape.

A "true" radial panel layout (no crosscut panels) handles the widely varying load paths these sails can have under different conditions. For light air use, of course, the .5 oz kites will fill sooner, but for all-around use, .75 oz or 1.5 oz (depending on boat size) delivers a more robust sail that can tolerate a bit more abuse (fun!).

Add a modern snuffer, such as the "ATN", and you can be sure to avoid any anxiety connected to setting, jibing or dowsing the sail, even short handed. Now all you have to do is decide whether to rig your sheets for "inside" or "outside" jibes!

Next Month: Rigging and Handling Your Asymmetrical Spinnaker

About the Author: Sandy Goodall, FX Sails Head of Design, has 30 years sailmaking experience and is the former technical director and head of design for Elvström Sails Denmark.

Related Links:
Standard Size Sails at The Sail Store
Custom Sails at FX Sails


DoubleEnder likes this.
administrator is offline  
Quote Quick Reply Share with Facebook
Sponsored Links
post #2 of 3 Old 02-26-2008
Jeff on <i>Beatrix</i>
Join Date: Aug 2007
Posts: 13
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Send a message via Skype™ to svbeatrix
Nice Article. Thanks
svbeatrix is offline  
Quote Quick Reply Share with Facebook
post #3 of 3 Old 05-20-2012
Senior Member
Join Date: Feb 2012
Location: New Orleans Louisiana
Posts: 3,236
Thanks: 10
Thanked 137 Times in 131 Posts
Rep Power: 6
Re: Inside the Asymmetrical Spinnaker

Very nice article, the only thing I would add is that with modern continuous line furlers it has become possible to use a roller furler on cruising asymetric spinnakers. These make it much easier to set and douse the sail as compared to an ATN sock. Because of the way the furlers work they also allow you to put the spinnaker up while at the dock and spend the day under the jib, then unroll the kite when you turn down, and roll up the jib.
Stumble is online now  
Quote Quick Reply Share with Facebook

Quick Reply

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page

Similar Threads
Thread Thread Starter Forum Replies Last Post
Where to buy asymmetrical spinnaker sanctuarysam Gear & Maintenance 18 10-04-2006 10:08 PM
Flying a spinnaker singlehanded jbr Seamanship & Navigation 2 09-07-2003 07:53 PM
Flying a spinnaker on a dinghy jbr Learning to Sail 0 09-04-2003 08:52 PM
Cruising Spinnakers (Symmetrical or Asymmetrical) couzensj Learning to Sail 2 06-24-2003 07:00 PM
Assymetric Spinnaker RPerreca General Discussion (sailing related) 2 06-09-2001 05:16 AM

Posting Rules  
You may not post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is Off
Smilies are On
[IMG] code is Off
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome