SailNet Community - Search Results
Advanced Search
Showing results 1 to 19 of 19
Search took 0.02 seconds.
Search: Posts Made By: 28islander
Forum: Islander   04-08-2012
Replies: 2
Views: 799
Posted By 28islander
Re: Islander 28 mast rake

I got a reply from another forum and the consensus was little or no rake. As in an inch or less. Will try and see how it goes.
Forum: Islander   04-05-2012
Replies: 2
Views: 799
Posted By 28islander
Islander 28 mast rake

Hi. I am replacing the standing rigging on my Islander 28 and was hoping someone could shed some light on how much rake the mast should have. Thanks for any input.
Forum: Islander   04-06-2011
Replies: 11
Views: 2,838
Posted By 28islander
try searching for rudder shaft tube repair in...

try searching for rudder shaft tube repair in google. I found the catalina site again that way. I used the west systems repair found in their manual. I worked just great. It's like new now.
Forum: Islander   03-16-2011
Replies: 5
Views: 1,305
Posted By 28islander
Joelozzy, I got a 10 gallon tank from Ronco,...

Joelozzy, I got a 10 gallon tank from Ronco, #B217. It fits under the starboard settee where the bladder tank used to sit.
Forum: Islander   02-01-2011
Replies: 5
Views: 1,305
Posted By 28islander
Thanks for the reply Paul. I guess there are not...

Thanks for the reply Paul. I guess there are not a lot of 2I8 owners out there with holding tank issues. I found a tank at Ronco that will fit in the starboard settee locker. I made a cardboard...
Forum: Gear & Maintenance   01-29-2011
Replies: 1
Views: 875
Posted By 28islander
Islander 28 holding tank

Hi, I also posted this in the Islander forum. My islander 28 has a holding tank under the starboard settee. Currently there is a very old flexible tank that measures about 27" X 33". Pretty sure it...
Forum: Islander   01-29-2011
Replies: 5
Views: 1,305
Posted By 28islander
28I holding tank

My islander 28 has a holding tank under the starboard settee. Currently there is a very old flexible tank that measures about 27" X 33". Pretty sure it is the original tank, in there since 1977. I...
Forum: Islander   11-16-2010
Replies: 5
Views: 1,193
Posted By 28islander
Yep, the port locker is it. If you mean the...

Yep, the port locker is it. If you mean the fittings on the upper end for the blower, try the Vetus catalog. In the ventilation section. Page 132 I think.
Forum: Islander   11-15-2010
Replies: 4
Views: 3,347
Posted By 28islander
Yes, I have read the references on proper tip to...

Yes, I have read the references on proper tip to hull clearance. Hence the questions I posed. I was hoping to get a response from other 2I8 owners who have repowered. I suspect they have the same...
Forum: Islander   11-15-2010
Replies: 4
Views: 3,347
Posted By 28islander
Prop to hull clearance

I am currently repowering my 2I8 with a Beta 20. This of course requires a new prop also. The old MD7A had a 12" prop installed. The clearance between the prop tip and the hull is about .5". I read...
Forum: Sailboat Design and Construction   11-09-2010
Replies: 24
Views: 6,048
Posted By 28islander
Hey erps, do you have any info on the compression...

Hey erps, do you have any info on the compression post repair? Any pictures or advice? Did the head bulkhead have to come out?
Paul
Forum: Islander   11-09-2010
Replies: 11
Views: 2,838
Posted By 28islander
Yes, there is a zerk fitting. In fact there were...

Yes, there is a zerk fitting. In fact there were two on mine, one at the upper end and one at the lower end. The lower one has been removed and glassed over because of a leak in the past. I was also...
Forum: Islander   11-08-2010
Replies: 11
Views: 2,838
Posted By 28islander
Well, I removed the rudder this weekend. No big...

Well, I removed the rudder this weekend. No big deal. I'm on the hard so I dug a little hole to lower the rudder down into. Just removed the tiller and cap. The rudder just slid down into the hole...
Forum: Islander   10-30-2010
Replies: 11
Views: 2,838
Posted By 28islander
Hi Down, I have a 1977 2I8, currently on the...

Hi Down, I have a 1977 2I8, currently on the hard. I plan on removing my rudder soon. Should be able to give you an update within a couple of weeks.
Paul
Forum: Islander   10-29-2010
Replies: 16
Views: 3,907
Posted By 28islander
Hey Paul, was replacing the floors a big deal?...

Hey Paul, was replacing the floors a big deal? Did you have to remove any cabinetry? I am considering doing the same thing.
Forum: Islander   09-11-2010
Replies: 23
Views: 5,291
Posted By 28islander
Thanks for all the information DL. I am looking...

Thanks for all the information DL. I am looking forward to having a reliable powerplant in our boat. Still haven't decided but think we are leaning toward the 20HP Beta Marine.
Forum: Islander   09-09-2010
Replies: 23
Views: 5,291
Posted By 28islander
Did you have to modify the engine bed? If so what...

Did you have to modify the engine bed? If so what needed to be done?
Forum: Islander   09-05-2010
Replies: 23
Views: 5,291
Posted By 28islander
Thanks for the reply DL. My wife and I were in...

Thanks for the reply DL. My wife and I were in Sidney a few weeks ago with our boat. We did see a very nice 2I8 while we were there but the owners were not around. It had a brown dodger. It would...
Forum: Islander   09-03-2010
Replies: 23
Views: 5,291
Posted By 28islander
Hey DL, I also have an Islander 28. The MD7A is...

Hey DL, I also have an Islander 28. The MD7A is dead of last week. Can you tell me any info on the repower? Cost, Who did it, how long it took etc...?
Showing results 1 to 19 of 19

 
 
For the best viewing experience please update your browser to Google Chrome