SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 9 of 9
Search took 0.01 seconds.
Search: Posts Made By: HernandoBeacher
Forum: General Discussion (sailing related) 10-02-2011
Replies: 3
Views: 778
Posted By HernandoBeacher
The control head provides the input interface to...

The control head provides the input interface to the smart pilot so it is necessary unless chart plotter serves that role.
Forum: Diesel 11-01-2010
Replies: 16
Views: 1,593
Posted By HernandoBeacher
Fill with hot oil

Can you soften the tube by refilling the engine with hot oil
Forum: Diesel 10-30-2010
Replies: 0
Views: 884
Posted By HernandoBeacher
3ym30

Are cylinders numbered from flywheel or pulley? The service manual is very detailed in terms of adjusting the Valves but doesn't specify the order of the cylinders.
Forum: General Discussion (sailing related) 06-17-2010
Replies: 10
Views: 1,135
Posted By HernandoBeacher
Displacement hulls deonstrate a power to speed...

Displacement hulls deonstrate a power to speed relationship based on the length at the waterline. The result is a speed at whichlarger increases in power are required to increase boat speed. /This...
Forum: Cruising & Liveaboard Forum 01-18-2010
Replies: 8
Views: 1,398
Posted By HernandoBeacher
Red face Plus One on Anclote Anchorage

Anclote anchorage near Dutchman Key provides shelter from all but easterly winds. From there the sand bar and pier to lighthouse is a short dingy ride.

Use extreme caution however in the Hernando...
Forum: General Discussion (sailing related) 10-15-2009
Replies: 1
Views: 562
Posted By HernandoBeacher
Check out the Regatta Pointe Marina in Palmetto....

Check out the Regatta Pointe Marina in Palmetto. it is located on the Manatee River about three miles from the entrance to the Tampa Shipping Channel.
Forum: Gear & Maintenance 10-11-2009
Replies: 7
Views: 949
Posted By HernandoBeacher
Oil extractor to primp fuel line

I have thought about fitting my oil extractor vacuum to the bleed screw when changing the fuel filter and allowing it to purge the air. I always try to do oil changes at the same time so it would...
Forum: Cruising & Liveaboard Forum 08-19-2009
Replies: 1
Views: 623
Posted By HernandoBeacher
There are a couple of marinas in Hernando Beach...

There are a couple of marinas in Hernando Beach that can handle your boat. You will have to enter the channel at a +3 high tide. I also draw 5'.
Forum: Gear & Maintenance 08-19-2009
Replies: 21
Views: 8,300
Posted By HernandoBeacher
I have not been able to replace the plastic...

I have not been able to replace the plastic threaded part of my new Lewmar wheel. Lewmar has been nonresponsive for eight months so I have half a folding wheel.

If anybody has any suggestions, I...
Showing results 1 to 9 of 9

 

All times are GMT -4. The time now is 06:18 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.