SailNet Community - Search Results
Advanced Search
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: S34
Forum: Diesel   01-13-2012
Replies: 25
Views: 3,956
Posted By S34
Unhappy Torresons won't ship to anywhere other than their...

Torresons won't ship to anywhere other than their dealership area for Yanmar parts.
That is either Cu coating or yellow electro-zinc because its steel underneath on the OEM lines. I coated mine with...
Forum: Diesel   01-12-2012
Replies: 39
Views: 4,123
Posted By S34
A running temperature of 120 F;That is luke warm...

A running temperature of 120 F;That is luke warm for a motor. You must have to use a different oil for those temps?


OK...I just found the answer. Good onya google.

"A salt water cooled engine...
Forum: Diesel   01-12-2012
Replies: 39
Views: 4,123
Posted By S34
That seems about standard for my 3GM30F. Seems to...

That seems about standard for my 3GM30F. Seems to be running a bit cold for my liking.Mine is the early model (1993). I don't know the alarm setting for mine. 62deg C seems too low for the alarm????
Forum: Diesel   01-12-2012
Replies: 16
Views: 4,153
Posted By S34
Just be gentle with the female spline. The...

Just be gentle with the female spline. The splines can be deformed easily, as I found out before I used the coach bolt method.(levering with a bar down the spline) A small triangular rat-tail file...
Forum: Diesel   01-03-2011
Replies: 16
Views: 4,153
Posted By S34
I had a 24" crescent, but it kept jumping off the...

I had a 24" crescent, but it kept jumping off the nut.:confused:
Forum: Diesel   01-03-2011
Replies: 16
Views: 4,153
Posted By S34
Finally got the time to attack the motor again. I...

Finally got the time to attack the motor again. I tried as you guys suggested.
But we don't have PB blaster here. Had to settle for CRC. Wouldn't budge after a day soak. So resorted to the method I...
Forum: Diesel   11-01-2010
Replies: 16
Views: 4,153
Posted By S34
I have already removed the bolts. ( With relative...

I have already removed the bolts. ( With relative ease)
Don't know how I would use a impact wrench to free the drive damper
from its seat though.
Forum: Diesel   10-29-2010
Replies: 16
Views: 4,153
Posted By S34
Not yet. I have had to shelve the project for a...

Not yet. I have had to shelve the project for a few weeks. Will report back when I have had time to get into it.
Forum: Diesel   10-12-2010
Replies: 16
Views: 4,153
Posted By S34
Email link seems to be defunct.It Was returned...

Email link seems to be defunct.It Was returned undelivered.
I am going to try a bolt head shoulder thru the spline, attached to a plate
bridging the raised edges of the outside face of the...
Forum: Diesel   10-11-2010
Replies: 7
Views: 2,286
Posted By S34
Mixing elbow for corrosion. The inner pipe can...

Mixing elbow for corrosion. The inner pipe can corrode thru without visible signs, letting raw water get perilously close to exhaust valves. Easy to check.
Mine is a 3gm30 F @ 500hrs and the elbow...
Forum: Diesel   10-11-2010
Replies: 16
Views: 4,153
Posted By S34
Yanmar 3gm30 F....removing Drive disc

Gidday,
I removed the trans on the above to clean and check. I have removed the retaining bolts on the drive disc but cannot seem to be able to get purchase on it to remove from flywheel. Can anyone...
Showing results 1 to 11 of 11

 
 
For the best viewing experience please update your browser to Google Chrome