SailNet Community - Search Results
Advanced Search
Showing results 1 to 25 of 27
Search took 0.02 seconds.
Search: Posts Made By: BluesHarp
Forum: Pacific Seacraft   04-28-2013
Replies: 2
Views: 1,290
Posted By BluesHarp
Re: Ryoko our PSC 31 is for sale

Oh NO Steve! How can you sell that beautiful boat?:confused:
Forum: Pacific Seacraft   04-01-2013
Replies: 14
Views: 1,864
Posted By BluesHarp
Re: New PSC 37 owner- need help with A/C

If I can remember correctly, I ran the main supply up to the corner behind the seat back and had it aiming up into the main cabin. I then "y"d it off with the intent of sending it towards the galley...
Forum: Pacific Seacraft   01-27-2013
Replies: 3
Views: 1,133
Posted By BluesHarp
Re: PSC34 Gear Reduction Ratio

Hi Wolfgang,
We have hull number 279 with the same engine that you have. Our transmission is a Kanzaki model KBW10 with a 2.14:1 reduction ratio. It is embossed in the label.
Neal
Forum: Pacific Seacraft   11-02-2012
Replies: 7
Views: 1,174
Posted By BluesHarp
Re: Hurricane Sandy

Glad to hear you are okay, but they should cancel that marathon! I might know where there is a stern rail that we took off a 37. It was solid and had no opening for a swim ladder if you are...
Forum: Pacific Seacraft   10-31-2012
Replies: 9
Views: 2,089
Posted By BluesHarp
Re: crealock34 fuel lift pump

I replaced the Walbro 1241 fuel pump on our 1994 PSC34 with a Walbro FRD1-1.
Forum: Pacific Seacraft   10-30-2012
Replies: 7
Views: 1,174
Posted By BluesHarp
Re: Hurricane Sandy

Sandy was 200 miles offshore when she passed Oriental NC and water was over the docks here on a creek off the Neuse River.

12549
Forum: Pacific Seacraft   09-12-2012
Replies: 8
Views: 1,710
Posted By BluesHarp
Re: Woohoo!! We're gonna be Crealock owners!

Great news. Welcome to the family!
Forum: Pacific Seacraft   09-04-2012
Replies: 7
Views: 702
Posted By BluesHarp
Re: need a new sink

We previously owned a 1985 PSC37 with a corroded sink and replaced it with a Scandvik two bowl galley sink. It was not a perfect fit and required some minor alterations to the counter top and...
Forum: Pacific Seacraft   08-27-2012
Replies: 7
Views: 936
Posted By BluesHarp
Re: fuel filler O-ring

I replaced the O-Ring in the diesel fill plate on the deck with a Perco # 0513DP3 1 1/2 inch.
Forum: Pacific Seacraft   08-01-2012
Replies: 9
Views: 1,144
Posted By BluesHarp
Re: Leaking hatches on PSC 37

My experience with hatches leaking is usually my mistake and not the boat's mistake.
Forum: Pacific Seacraft   03-28-2012
Replies: 1
Views: 888
Posted By BluesHarp
Re: Interior Teak Oil Color Matching

We have had our best luck using Minwax Helmsman Semi Gloss trying to match the original factory varnish finish on Bluesharp.
Forum: Pacific Seacraft   03-27-2012
Replies: 16
Views: 2,899
Posted By BluesHarp
Re: How low can you run your fuel tank

I cut the sole with a hole saw and inserted a bronze deck fill to make it easier to read my fuel gauge. Now I don't have to lift floor boards in order to verify fuel levels.
10411
Forum: Pacific Seacraft   11-16-2011
Replies: 10
Views: 2,170
Posted By BluesHarp
Our earlier PSC37 Podjo had a mount for a raft...

Our earlier PSC37 Podjo had a mount for a raft installed just forward of the mast.
Forum: Pacific Seacraft   11-15-2011
Replies: 11
Views: 1,768
Posted By BluesHarp
Nice! The smile on your face says it all!

Nice! The smile on your face says it all!
Forum: Pacific Seacraft   11-14-2011
Replies: 5
Views: 1,211
Posted By BluesHarp
Locations

On our 37, the inverter was under the chart table. It was a short distance to the batteries. On our current 34, the chart table is not on the same side as the batteries, so longer runs .... drats. ...
Forum: Pacific Seacraft   09-01-2011
Replies: 8
Views: 1,893
Posted By BluesHarp
I might be wrong, but if your mast is carrying...

I might be wrong, but if your mast is carrying the negative, then you will not be able to use a polarity reversing switch. You sure do not want to send a positive charge into your mast if the mast...
Forum: Pacific Seacraft   08-30-2011
Replies: 21
Views: 3,695
Posted By BluesHarp
My barometer here in New Bern, NC hit a new all...

My barometer here in New Bern, NC hit a new all time low. I had left the pointer at the low when the eye of Charlie went over our house in Calabash. It was 29.1 then. The new low we saw when the...
Forum: Pacific Seacraft   08-15-2011
Replies: 4
Views: 1,553
Posted By BluesHarp
That is odd. I would think that the weight of...

That is odd. I would think that the weight of the chain because of the distance of the fall would provide enough pull.
Forum: Pacific Seacraft   08-15-2011
Replies: 4
Views: 1,553
Posted By BluesHarp
See this link to download a PDF manual. ...

See this link to download a PDF manual.

http://www.muir.com.au/shop/manuals/VMC%20500.pdf.

On our Muir electric, I use a handle to rotate the top squared socket counter clockwise to unlock...
Forum: Pacific Seacraft   08-10-2011
Replies: 16
Views: 2,200
Posted By BluesHarp
We have 200 feet of 5/16 on our 34 and when I put...

We have 200 feet of 5/16 on our 34 and when I put in all back in recently after marking the chain, I had to adjust the pile in the locker. It would pile up too high to fit more chain without pushing...
Forum: Pacific Seacraft   06-07-2011
Replies: 11
Views: 4,219
Posted By BluesHarp
I plan to try a Prussic knot a few feet up from...

I plan to try a Prussic knot a few feet up from the deck with some thin cord and seeing if I can get enough purchase on the stay to tighten it to an open turnbuckle.
Forum: Pacific Seacraft   03-21-2011
Replies: 8
Views: 1,142
Posted By BluesHarp
The factory has gone to stainless steel because...

The factory has gone to stainless steel because of the paint bubbling issue, but I cannot recall which brand. We have removed the 'glass', wire brushed, used 2 part zinc chromate, followed by...
Forum: Pacific Seacraft   02-25-2011
Replies: 10
Views: 3,125
Posted By BluesHarp
Thanks for putting this together...nice.

Thanks for putting this together...nice.
Forum: Pacific Seacraft   02-25-2011
Replies: 16
Views: 3,076
Posted By BluesHarp
Pull the tank

Another option is to remove the two floor boards and pull the tank out. Seems like it would be easier to work on the tank in your garage on a work bench. That would give you good access to all...
Forum: Pacific Seacraft   02-25-2011
Replies: 8
Views: 1,496
Posted By BluesHarp
What size boat?:)

What size boat?:)
Showing results 1 to 25 of 27

 
 
For the best viewing experience please update your browser to Google Chrome