SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 8 of 8
Search took 0.01 seconds.
Search: Posts Made By: BenMerc
Forum: Gear & Maintenance 04-10-2014
Replies: 25
Views: 1,055
Posted By Ferretchaser
Re: Lower rudder bushing

If you give me the measurements and a scetch, I can machine the bits you want out of bronze for you. I probably have the bar stock on board

ATB

Michael
Forum: Gear & Maintenance 04-10-2014
Replies: 25
Views: 1,055
Posted By rikhall
Re: Lower rudder bushing

Benmerc - you were looking at the wrong place - there are bunch of us that have replaced that lower bushing. And, it is the same bushing on quite a few sized Irwins. Here is one set of information...
Forum: Gear & Maintenance 04-09-2014
Replies: 25
Views: 1,055
Posted By Delta-T
Re: Lower rudder bushing

Funny you should suggest that. I was not going to mention it because of fear of being jump all over...I did just that to my lower shoe two days ago and it came out great. My shoe is much like...
Forum: Gear & Maintenance 04-09-2014
Replies: 25
Views: 1,055
Posted By MarkSF
Re: Lower rudder bushing

The bronze on bronze approach used on my Bristol lasted 30 years and at least 10,000 hours of use, so I'm inclined to think it has something going for it.
Forum: Gear & Maintenance 04-09-2014
Replies: 25
Views: 1,055
Posted By CalebD
Re: Lower rudder bushing

West system also sells the graphite powder to make a low friction surface.

I'd wipe a thin layer of vaseline on only the rudder shaft before pouring the epoxy; this will act as a mold release once...
Forum: Gear & Maintenance 04-09-2014
Replies: 25
Views: 1,055
Posted By MarkSF
Re: Lower rudder bushing

Delrin is a machinable plastic so you need an ordinary machine shop, not a plastic fabricator. It would be made on an ordinary lathe.

You need to make a drawing or sketch of what you want, and...
Forum: Gear & Maintenance 04-09-2014
Replies: 25
Views: 1,055
Posted By jsaronson
Re: Lower rudder bushing

Looks like something a machine shop could make out of delrin.
Forum: Gear & Maintenance 04-08-2014
Replies: 25
Views: 1,055
Posted By Delta-T
Re: Lower rudder bushing

Got any pictures, it would help.
Showing results 1 to 8 of 8

 

All times are GMT -4. The time now is 02:58 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.