SailNet Community - Search Results
Advanced Search
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: aruggiero
Forum: Gear & Maintenance   08-31-2009
Replies: 0
Views: 976
Posted By aruggiero
Jabsco Macerator Pump

We had to replace the macerator pump on our Jabsco electric head. The old macerator had started leaking. It worked fine with the old pump but since we put the new one on it is either drawing in too...
Forum: Seamanship & Navigation   03-18-2008
Replies: 41
Views: 4,252
Posted By aruggiero
TacPac

I would love to have a copy of this - we are newbees to saltwater and trying to make sure we have all the procedures down is very important to us.
Forum: Gear & Maintenance   02-14-2007
Replies: 1
Views: 1,025
Posted By aruggiero
Water Tanks

I have posted this twice because when I tried to start a new thread earlier it kept saying I didn't have permission. We have a 1980 37 Endeavour that has a 100 gallon water tank, We have a problem...
Forum: Gear & Maintenance   02-14-2007
Replies: 4
Views: 963
Posted By aruggiero
Water Tank

I know I am not posting this right but I can't figure out how to post a new message. We have a 1980 37 Endeavour that has a 100 gallon water tank, We have a problem with one of the outlets on the...
Forum: Gear & Maintenance   02-14-2007
Replies: 23
Views: 2,390
Posted By aruggiero
We just replaced the countertops on our boat with...

We just replaced the countertops on our boat with the same problem - the teak trim around the outside. We could not get the trim off. We got a router bit - roman-ogee is what it was called and it...
Forum: Gear & Maintenance   07-24-2006
Replies: 3
Views: 807
Posted By aruggiero
We bought the stove used so there are no...

We bought the stove used so there are no installation instructions with it. It is a marine stove and it is gimballed. The original cutout was for a 3-burner lpg range and the stove we just bought...
Forum: Gear & Maintenance   07-24-2006
Replies: 3
Views: 807
Posted By aruggiero
New stove

We purchased a new lpg stove for our boat and we are getting ready to install it. The one that came with our boat didn't have an oven. The cutout for the stove is exposed fiberglass in the back. ...
Forum: General Discussion (sailing related)   07-20-2006
Replies: 2
Views: 740
Posted By aruggiero
Engine Paint

Our engine is in need of a paint job. We have never painted an engine before and none of the maintenance books/manuals cover the topic. Is there anything that should be covered on the engine...
Forum: Announcements and Suggestions Box   07-19-2006
Replies: 3
Views: 3,547
Posted By aruggiero
Cutting fiberglass

We have bought new ports for our boat. There are two sizes but the larger one is a little bigger than the actual cutout for the old ports. I was just wondering what is the best tool to use for...
Forum: General Discussion (sailing related)   07-12-2006
Replies: 6
Views: 1,734
Posted By aruggiero
It is a cored deck. We haven't filled it with...

It is a cored deck. We haven't filled it with epoxy yet but we plan to - the plywoood that is there is screwed in and it doesn't appear to be sealed. The trim ring screws on with #6 screws. The...
Forum: General Discussion (sailing related)   07-11-2006
Replies: 6
Views: 1,734
Posted By aruggiero
Deck Prism

We recently bought an old boat that we are currently restoring. In the cockpit there was a big hole that had a piece of plywood screwed on over it. We decided to put a deck prism there to fill...
Showing results 1 to 11 of 11

 
 
For the best viewing experience please update your browser to Google Chrome