SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 12 of 12
Search took 0.01 seconds.
Search: Posts Made By: Perseverance
Forum: Gear & Maintenance 02-18-2013
Replies: 27
Views: 1,553
Posted By Perseverance
Re: BOLT head in the Bilge...

8.8 refers to the hardness and indicates that it is metric probably 10 mm. Can be one of two thread pitches. 8.8 it the most common of hardened metric bolts and should be easy to find.
Forum: Gear & Maintenance 02-17-2013
Replies: 27
Views: 1,553
Posted By Perseverance
Re: BOLT head in the Bilge...

Looks pretty urgent to me. Looks like the engine allignment will shift if the bracket swings. It doesnt look to difficult to repair, there may be enough bolt sticking out to get ahold of with a good...
Forum: Boat Review and Purchase Forum 02-10-2013
Replies: 9
Views: 968
Posted By Perseverance
Re: Gelcoat cracks in Sabre

As you can see most cracks will begin at a screw hole. That is because gelcoat is like a brittle layer on top of a more flexible structure layer. Many could be avoided by proper beveling at screw...
Forum: General Discussion (sailing related) 02-01-2013
Replies: 153
Views: 27,407
Posted By Perseverance
Re: Clothing optional sailing

Id be afraid someone would ask if that is the first or second reef.
You know what they say about men with big boats.
Forum: Gear & Maintenance 01-28-2013
Replies: 22
Views: 2,912
Posted By Perseverance
Re: How often do I need to replace my cutlass bearing?

Most cutlass bearings are compressed rubber and any play would indicate some wear. Some, like mine are machined hard plastic and a certain amount of play is acceptable. Mine for a 1.5 in shaft is...
Forum: Diesel 01-28-2013
Replies: 0
Views: 238
Posted By Perseverance
crankshaft bolt pattern 4.236

Does anyone have a drawing of the bolt pattern for the crankshaft pully on a Perkins 4.236. I have installed a cruise ro water maker that works great but need more rpm options.
Forum: Gear & Maintenance 08-22-2012
Replies: 11
Views: 988
Posted By Perseverance
Re: Bottom/Top Painting-What Comes 1st?

Wet often is ok with topside paint. Under water is not. I strongly recomend you prime bottom with interlux 2000e if it is clean to bare plastic. It will make your job last much longer for the cost....
Forum: General Discussion (sailing related) 08-15-2012
Replies: 12
Views: 2,579
Posted By Perseverance
Re: Sailing outside on the East Coast

Thank you very much for all the advice. I hope to come out the New York harbor about Oct 10th. I need to stay attached to the east coast till after Thanksgiving. I want to get as far down as I can by...
Forum: General Discussion (sailing related) 08-06-2012
Replies: 6
Views: 391
Posted By Perseverance
Re: St. Lawrance ?

Americans do not need a pasport to go in or out of Canada. I found going in very easy in lake huron. Coming back is much easier if you preregister your boat with customs. You may not be coming back...
Forum: General Discussion (sailing related) 08-06-2012
Replies: 12
Views: 2,579
Posted By Perseverance
Re: Sailing outside on the East Coast

No can do says the Admiral. I am thinking off Jacksonville. I can run 7 on fuel forever almost (1500 mi). Anyone else going about that time.
Forum: General Discussion (sailing related) 08-05-2012
Replies: 12
Views: 2,579
Posted By Perseverance
Sailing outside on the East Coast

I am sailing from Michigan to Puerto Rico this fall and I am too tall to go the ICW below Norfolk. I plan to come out the NY harbor about mid Oct and get down as far as time allows me before...
Forum: Introduce Yourself 10-05-2010
Replies: 1
Views: 435
Posted By Perseverance
new member

I am looking for like minded people who love sailing. I have been refitting a 45 ft steel sailboat that I plan to take to the caribean in 2 years from Michigan. I have been sailing in both places for...
Showing results 1 to 12 of 12

 

All times are GMT -4. The time now is 06:59 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012