SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 9 of 9
Search took 0.01 seconds.
Search: Posts Made By: capecapt
Forum: Gear & Maintenance 04-20-2011
Replies: 2
Views: 1,790
Posted By capecapt
Eletronic tach/alernator problems

Hello,

Almost all electronic tachs work on the output of the alternator. The is a seperate terminal on most tachs that is designated for this purpose. If the output stops for any reason, which...
Forum: Gear & Maintenance 04-05-2011
Replies: 59
Views: 6,392
Posted By capecapt
To ease the chore of hauling any size anchor you...

To ease the chore of hauling any size anchor you may choose, try a snatch block to fairlead the anchor rode to a primary winch. When the load gets greater than you can manually hual, crank away. This...
Forum: Cruising & Liveaboard Forum 04-03-2011
Replies: 4
Views: 1,140
Posted By capecapt
Fort Pierce Inlat

Hello, I have spent the winter at Pelican Yatch Club on Fort Pierce inlet. It is secure, clean and very resonable. The staff are friendly, help with your lines, and will actually keep an eye on your...
Forum: Boat Review and Purchase Forum 01-27-2011
Replies: 2
Views: 828
Posted By capecapt
Try to find Patton Marine Surveyors. They are...

Try to find Patton Marine Surveyors. They are expensive, but extremely thorough, and the survey will be excepted by all major insurance companies.
Good luck!
Forum: Gear & Maintenance 01-13-2011
Replies: 12
Views: 1,082
Posted By capecapt
I had a similar situation on my vessel. The thru...

I had a similar situation on my vessel. The thru hull fitting for the B&G speedo was not properly installed, and I ended up with water intrusion in the hull. This was verified with a moisture meter,...
Forum: Gear & Maintenance 01-09-2011
Replies: 113
Views: 10,659
Posted By capecapt
I have just purchased a Manson Supreme, 100lb for...

I have just purchased a Manson Supreme, 100lb for my 62' cutter.
I have had a CQR 60lb on 1/2 inch G4 chain, handled by a Lewmar 3500 hydraulic windlass. I have found that the CQR needed to be set...
Forum: Gear & Maintenance 09-27-2009
Replies: 8
Views: 1,183
Posted By capecapt
You might try looking for a used mast on E-bay,...

You might try looking for a used mast on E-bay, or at a local salvage yard. It looks like you had a lot of electrolis or corrosion on the base of the mast. Good Luck
Forum: Gear & Maintenance 09-21-2008
Replies: 15
Views: 7,042
Posted By capecapt
50/60 isolators

You can purchase units from companies such as Charles or Mastervolt that will take either 50 or 60 hz in and put out a clean 60 for your equipment, if that is what you need. If you plan international...
Forum: Gear & Maintenance 09-04-2008
Replies: 17
Views: 1,848
Posted By capecapt
I have been on a three-four year retrofit of a...

I have been on a three-four year retrofit of a Perry designed cutter, and Lewmar has given me a run around for most of it. Very slow at getting back to me, wait forever for parts.....fired all...
Showing results 1 to 9 of 9

 

All times are GMT -4. The time now is 06:40 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012