SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: celenoglu
Forum: Gear & Maintenance 11 Hours Ago
Replies: 7
Views: 222
Posted By celenoglu
Re: clevis pin, 18-8 or 316?

Galvanic corrosion is the result of different voltage potentials of different metals immersed in salt water. The voltage difference of 18-8 and 316 is very low. This will not cause galvanic corrosion...
Forum: Gear & Maintenance 15 Hours Ago
Replies: 7
Views: 222
Posted By celenoglu
Re: clevis pin, 18-8 or 316?

Use 316, 18-8 is generic for other 300 series. Cotter pins are more secure than split rings for retaining the clevis pin.
Forum: Gear & Maintenance 21 Hours Ago
Replies: 6
Views: 353
Posted By celenoglu
Re: Caulk for toerail...

The method you are planning is like positioning a kettle when water drops from a leaking ceiling. Repair the ceiling, rebed the stachions.
Forum: Gear & Maintenance 1 Week Ago
Replies: 17
Views: 824
Posted By celenoglu
Re: Rudder Replacement Problems

Two possible reasons:

1. The rudder from Catalina is defective.
2. "Drilled the shaft" means something done with tools. The rudder is misaligned, it is not in line with the boat.
Forum: General Discussion (sailing related) 1 Week Ago
Replies: 14
Views: 738
Posted By celenoglu
Re: Winter in the water

Igloo's are built from ice and the temperature inside is much higher. If you really think to heat the boat, a 100 W lamp might be all you need.

Another important point: Freezing water generally...
Forum: General Discussion (sailing related) 1 Week Ago
Replies: 14
Views: 738
Posted By celenoglu
Re: Winter in the water

If the water freezes, the last thing you have to worry are the thruhulls. Inside the boat the temperature will be a lot higher than that of outside.
Forum: General Discussion (sailing related) 2 Weeks Ago
Replies: 107
Views: 4,137
Posted By celenoglu
Re: Spinaker or Genaker - which do you prefer?

A gennaker is a good answer. Although it will not work DDW you can rig it as you do with a spinnaker, and that means it will work as a spinnaker although a little bit smaller.
Forum: Gear & Maintenance 2 Weeks Ago
Replies: 50
Views: 3,312
Posted By celenoglu
Re: How do these seacocks look?

Use bronze, marelon is relatively new, so do not be the pionee to test.
Reuse the hole.
Backing plate can be made of many materials, make sure they are though enough.
Forum: Gear & Maintenance 2 Weeks Ago
Replies: 50
Views: 3,312
Posted By celenoglu
Re: How do these seacocks look?

They look just a little bit better than direct holes. Replace them.
Forum: Boat Review and Purchase Forum 10-19-2014
Replies: 22
Views: 1,515
Posted By celenoglu
Re: Wooden Turkish Gulet? Are they good charter sailboats?

The gulets are worth to consider. They are working in charter business in Turkey. I recomend them for charter, but the boat should be surveyed. You can also contact "Aegean Boats" for a planned...
Forum: Gear & Maintenance 10-07-2014
Replies: 14
Views: 1,254
Posted By celenoglu
Re: I think I stuffed my furler. What do you think?

The angle between the halyard and the forestay should be more than 7 degrees, otherwise the halyard wounds around the forestay and the forestay breaks after some time. You should attach a block to...
Forum: Gear & Maintenance 10-01-2014
Replies: 101
Views: 4,869
Posted By celenoglu
Re: Request for Comments: DIY Tether

I also didnot like the carabinier hook. The load carrying capacity for these hooks are very low. If your intend is to stay on the boat the hook might be enough but the line you use is overkill for...
Forum: Gear & Maintenance 09-28-2014
Replies: 2
Views: 470
Posted By celenoglu
Re: atwood LED lights

Only a few LED lights are acceptable for navigation. Although the amount of light measured is more than normal bulbs, the light frequency is not visible to the human eye as much as the hot lights....
Forum: General Discussion (sailing related) 09-23-2014
Replies: 5
Views: 561
Posted By celenoglu
Re: Cape Cod on the outside

There is a saying in Turkish: The shortest route is the one you know.

I do not know the conditions of the area. I think it is best to take the route you know.
Forum: Gear & Maintenance 09-23-2014
Replies: 18
Views: 1,274
Posted By celenoglu
Re: Head to Farymann A30M

The cooling jackets can be manufactured from plastic pipes. I have done it a few years ago, they are still working.
Forum: Gear & Maintenance 09-22-2014
Replies: 3
Views: 372
Posted By celenoglu
re: Yanmar 4jhte - symptoms of mixing elbow?

Replace the mixing elbow. RPM and fuel consumption will return to normal. This has nothing to do with fuel return. Check all the return lines and clean if needed. Specially the connection points...
Forum: Boat Review and Purchase Forum 09-22-2014
Replies: 20
Views: 1,299
Posted By celenoglu
Re: Concerned about condition of the mast before buying. Advice?!

The boat is not properly taken care of. The bolts and nuts, the foot of the mast, even the hose clamps on the hoses of bilge pump, and the connection of two pieces of hose tells me to keep clear.
Forum: General Discussion (sailing related) 09-20-2014
Replies: 2
Views: 295
Posted By celenoglu
Re: Staysail furler deck attachment, ect

A backing plate is hardly enough for a storm staysail. Normally the connection point should go down to the hull. You can use the same size wire as your forestay or backstay. You should also be using...
Forum: Seamanship & Navigation 09-20-2014
Replies: 9
Views: 769
Posted By celenoglu
Re: Tacking ketch rig sharpie

If you wish to sail with all your sails, you can backwind the mizzen by pushing the boom with your hand when in irons.
Forum: Seamanship & Navigation 09-20-2014
Replies: 9
Views: 769
Posted By celenoglu
Re: Tacking ketch rig sharpie

You shuld be using the jib and the main while close hauled. The main is blanketed by the jib. This causes the main not to work properly and you cannot tack. Use your jib and mizzen sail only for...
Forum: Gear & Maintenance 09-17-2014
Replies: 8
Views: 606
Posted By celenoglu
Re: Galley sink drain location

It is much better to locate it on the waterline. "Sitting water" is generally debris and block the drain if it is below the waterline. If you drain to the waterline everything will flow outside. As...
Forum: Cruising & Liveaboard Forum 09-16-2014
Replies: 30
Views: 1,589
Posted By celenoglu
Re: Cruising gear advise needed "LIST"

Replace standing rigging
Forum: Gear & Maintenance 09-15-2014
Replies: 12
Views: 721
Posted By celenoglu
Re: minor damage to teak toe rail

Use epoxy as the glue. The trick is to clean the parts with acetone prior to glueing. Damp a piece of cloth with acetone and clean the areas to be glued. Wait till the wood is dry and apply epoxy. If...
Forum: Gear & Maintenance 09-08-2014
Replies: 80
Views: 4,230
Posted By celenoglu
Re: Sorry, you are about to get slammed. First question: bowsprit

Use a drilling tool or a knife to clean inside the rotten area. If it is not too deep you can clean most of it. Brush some epoxy inside and fill with wood saw dust mixed epoxy. The rot size will not...
Forum: Living Aboard 09-04-2014
Replies: 7
Views: 386
Posted By celenoglu
Re: wintering in Greece. save ports.

Mytilini Marina (http://www.seturmarinas.com/en/marinas/mytilini-marina)
Showing results 1 to 25 of 500

 

All times are GMT -4. The time now is 03:07 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.