SailNet Community - Search Results
Advanced Search
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: csilva
Forum: Gear & Maintenance   07-23-2010
Replies: 2
Views: 943
Posted By csilva
Changing instruments

I am planning to replace an Ockam system on my Tripp 33 sailboat. As a starter, I am thinking of a TACT033 Tacktick Entry Level Wind System (12v Display, Wireless Wind Transmitter) which I assume...
Forum: Announcements and Suggestions Box   02-18-2010
Replies: 1
Views: 912
Posted By csilva
I am also trying to find them so please let me...

I am also trying to find them so please let me know if you sicceded.

Another issue I have with my system (an old 001 cpu model) is connecting a GPSMAP421s on the network. Any ideas? I would hete...
Forum: Electronics   12-16-2009
Replies: 4
Views: 1,367
Posted By csilva
Ok, seems it is the same. Thanks,

Ok, seems it is the same.
Thanks,
Forum: Electronics   12-16-2009
Replies: 4
Views: 1,367
Posted By csilva
Thanks. Do you know the model of your tranducer?...

Thanks. Do you know the model of your tranducer? Mine says it is a "transmon mount depth and temperature transducer, 50/200 kHz" and yes, I believe the hull is solid (I will double chack, though).
Forum: Electronics   12-15-2009
Replies: 4
Views: 1,367
Posted By csilva
GARMIN GPSMAP 421s

Has anyone experienced with a shoot-thru-hull transom transducer installation? Seems nice to avoid drilling a hole in the hull, but what happens to the sonar sensitivity? The installation...
Forum: Gear & Maintenance   10-01-2009
Replies: 4
Views: 3,274
Posted By csilva
Rotavecta Reinstallation

I re-installed only to find it did not work. Apparently it was damaged when dismasted and I need to change the transducer. Checked the Raymarine site and found that I could use the D240 replacement...
Forum: Gear & Maintenance   05-28-2009
Replies: 4
Views: 3,274
Posted By csilva
Rotavecta wind transducer

I am re-installing my wind transducer and noticed that it might need some maintenance due to salty conditions. Any advice on type of maintenance I should perform?

Thanks,
Forum: Gear & Maintenance   07-28-2008
Replies: 11
Views: 1,581
Posted By csilva
bus bars vs. terminal blocks

What if I use a bus bar for the negative cables and a terminal block for the positive? Better yet, what if I run down the mast with only one negative wire for all the lights (actually, only 3...
Forum: Gear & Maintenance   06-22-2008
Replies: 11
Views: 1,581
Posted By csilva
Thanks again.

Thanks again.
Forum: Gear & Maintenance   06-22-2008
Replies: 11
Views: 1,581
Posted By csilva
Thanks. Just in time to change my purchase. I...

Thanks.
Just in time to change my purchase. I guess now I will buy WestMarine's 214991 (sorry, got a message that I cannot send images.
Forum: Gear & Maintenance   06-15-2008
Replies: 11
Views: 1,581
Posted By csilva
Thanks

Thank you all for the good advice. The coax antena and wind instruments cables are already cut but poorly connected, therefore I will definitely spend on good connectors, including bus bars.
Forum: Introduce Yourself   06-14-2008
Replies: 3,452
Views: 957,642
Posted By csilva
La Punta, Callao, PERU

La Punta, Callao, PERU
Forum: Gear & Maintenance   06-14-2008
Replies: 11
Views: 1,581
Posted By csilva
mast electrical wiring

I am planning an overhaul of my electrical system and wonder if I should use a junction box at the cabin entrance of the mast wiring in order to avoid chafe and also ease any further mast...
Forum: Introduce Yourself   02-26-2006
Replies: 3,452
Views: 957,642
Posted By csilva
Callao, PERU

Callao, PERU
Forum: Gear & Maintenance   06-03-2002
Replies: 9
Views: 4,658
Posted By csilva
Raytheon Bidata ST 40

I have an ST 40 Wind Instrument with Rotavecta transducer already installes and plan to install an ST 40 Bidata mainly to connect both so that I can get true wind speed and angle.
Do I also need to...
Showing results 1 to 15 of 15

 
 
For the best viewing experience please update your browser to Google Chrome