SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 25 of 76
Search took 0.01 seconds.
Search: Posts Made By: JeffBurright
Forum: Gear & Maintenance 8 Hours Ago
Replies: 32
Views: 984
Posted By JeffBurright
Re: Remove embedded carriage bolts, then my strut, on the water?

Hi again,
Thanks to all for a good discussion. I was out at the islands trying to straighten the strut underwater with a portable press made out of scrap materials, but the bronze was stronger than...
Forum: Gear & Maintenance 1 Week Ago
Replies: 32
Views: 984
Posted By JeffBurright
Re: Remove embedded carriage bolts, then my strut, on the water?

Can I beach a cold molded fin keel boat without causing structural damage? It doesn't help me get the bolts out, but I wouldn't be opposed to it necessarily.
Forum: Gear & Maintenance 1 Week Ago
Replies: 32
Views: 984
Posted By JeffBurright
Remove embedded carriage bolts, then my strut, on the water?

All right you boat repair geniuses, put on your head scratching caps. I got one for you.

The strut for my prop shaft got bent by a rude mooring line and now has a little banana curve, and my...
Forum: Seamanship & Navigation 10-15-2013
Replies: 13
Views: 1,487
Posted By JeffBurright
Re: Anchor rode keeps wrapping around fin keel - can we prevent it?

You all are awesome. This is exactly what I needed. Last night I wrapped soft lead ribbon around a spare zinc and slid it down the rode with a carabiner as gfh suggested (probably somewhere just...
Forum: Seamanship & Navigation 10-14-2013
Replies: 13
Views: 1,487
Posted By JeffBurright
Anchor rode keeps wrapping around fin keel - can we prevent it?

Hi all,
We are in an estuary with a 3 knot tidal current, and twice in the last two days we have had our rode wrap around our fin keel necessitating fancy acrobatics to disentangle it. We keep the...
Forum: Gear & Maintenance 07-05-2013
Replies: 63
Views: 5,468
Posted By JeffBurright
Re: Cost to Replace Chainplates? Should I Walk Away?

As far as DIY yards, I recommend the Ilwaco boat yard at the mouth of the Columbia River. We hauled out our 30' boat there, had a bottom wash and did a month's worth of heavy work on her -...
Forum: Gear & Maintenance 06-01-2013
Replies: 30
Views: 2,959
Posted By JeffBurright
Re: Self Tailing Winches

Self tailing winches are amazing. That is all.

That is not all. It is so nice to be able to make micro-adjustments to your sails with one hand. Laziness? Perhaps. But isn't well-engineered...
Forum: Electronics 05-27-2013
Replies: 12
Views: 2,097
Posted By JeffBurright
Re: Anyone using bluetooth GPS rcvr with wifi only iPad?

Somewhat similar deal - I have a Delorme InReach GPS sat tracker with bluetooth (similar to SPOT but with global coverage and 2-way texting), which I hook into via my iPhone. I have no cell provider...
Forum: Gear & Maintenance 05-26-2013
Replies: 9
Views: 727
Posted By JeffBurright
Re: Tiller pilot mount

We did exactly this on our boat. Raymarine sells the tiller bracket for $45-50, but I had one made by a local machinist for $20. When the autopilot is not in use, all you see is the bracket and the...
Forum: General Discussion (sailing related) 04-14-2013
Replies: 6
Views: 1,730
Posted By JeffBurright
Re: What is a "Catalina smile" in regards to the Keel?

We had one on our boat, which required weeks of work and a few thousand dollars to repair correctly (in our eyes). Here's a link to a post with pictures of our smile: Take to the sea: Stranded at the...
Forum: Gear & Maintenance 02-12-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

As an update, we received a replacement flange and locking nut from a friend who came to visit us from back home. We also decided to replace the engine mounts, as one of the adjustment bolts spun in...
Forum: Boat Review and Purchase Forum 02-02-2013
Replies: 8
Views: 2,140
Posted By JeffBurright
Re: Nightingale 30

Holy cow! I own a Nightingale 30 sloop and I thought it was the only one he ever made! I know this is an old thread, but I'd be curious to know if the original poster ever picked up this boat. I'd...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

Thanks Gary for the good advice. Unfortunately the hammer blows were my no-no. I used a wood chisel to pry the two coupling pieces apart. I think heat/dirt/rust conspired to glue the two pieces...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

Ha! Harmony already got out the wood burner and engraved it in the transom.

Thanks for the tip on Cabo Yacht Center, gentlemen. I've got a poorly worded Spanish email waiting in their inbox as of...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

It would be a pain to put the flange back on to try now, but from what I remember, once the flange was pushed all the way in it was a tight fit.

Capt. Gary Randall, I'm with you that the flange...
Forum: Gear & Maintenance 01-30-2013
Replies: 9
Views: 584
Posted By JeffBurright
Re: Solar and Wind setups...?

You and I are probably in different leagues, but on my boat I have one charge controller for two 70W flexible panels and a ~60W wind turbine. All generation sources are tied straight to the 200Ah...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

Here's the best I could come up with using the part number from my Yanmar guy in Portland.

http://i81.photobucket.com/albums/j239/burrighj/NewPicture_zpsfd8f7e2e.jpg

This syncs up with the...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

This is the same nut that originally failed. I reused it by filing off the older calked spot. The threads look good on the nut still, nearly perfect with minor scoring. I plan to replace this nut now...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

This is how it looks in the schematics for the transmission, plus you have to have it this way in order to do the calking.

We used to keep the transmission in neutral under sail, but on the ocean...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Re: Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

Faster: That's correct, the two coupling faces did not separate. The entire coupling came off the back of the transmission via the output spline, after the locking nut backed off.

I agree that...
Forum: Gear & Maintenance 01-30-2013
Replies: 33
Views: 3,193
Posted By JeffBurright
Transmission output flange fell off Yanmar 2QM15 - Theories re: why?

Hello,
I recently had the output coupling from my Yanmar 2QM15 transmission fall out while underway (we didn't hit anything), disconnecting the prop shaft as a result. I'm in the process of...
Forum: Cruising & Liveaboard Forum 01-14-2013
Replies: 6
Views: 3,886
Posted By JeffBurright
Re: Seattle - I am looking for a liveaboard slip

Howdy,
I went through the process of finding a liveaboard slip in Seattle a few years ago, so I can tell you what I remember. I called around to all the marinas I could find in the span of a week or...
Forum: Seamanship & Navigation 11-29-2012
Replies: 16
Views: 3,075
Posted By JeffBurright
Re: How do you fold sails on deck?

Oh, to have hanks! Unfortunately in this case, we have a head foil system with luff tape on our foresails. It sure is nice for raising/lowering quick, but the hanks would be so much nicer for...
Forum: Seamanship & Navigation 11-29-2012
Replies: 16
Views: 3,075
Posted By JeffBurright
How do you fold sails on deck?

Like the subject says, I'm looking for ideas on how to fold our foresails when we are at anchor and don't have the square footage of a dock to lay them out. We have a 30' boat, so deck space is...
Forum: Gear & Maintenance 09-17-2012
Replies: 8
Views: 783
Posted By JeffBurright
Re: Rot in hull/deck joint - thoughts on necessity of reinforcement?

Hmm, now that you parse out the two types, I'm not sure. When we bought it four years back we were told that it was cold-molded in the style of the Gougeon Brothers, but it's also true that it is a...
Showing results 1 to 25 of 76

 

All times are GMT -4. The time now is 02:40 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.