SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 25 of 54
Search took 0.01 seconds.
Search: Posts Made By: NCboatrx
Forum: Diesel 1 Week Ago
Replies: 9
Views: 336
Posted By NCboatrx
Re: Stop cable

This looks like a Teleflex cable so there should be a small locknut behind the T handle. Use a 5/16" wrench and undo this locknut and then the handle should unscrew with ease.
Forum: Diesel 4 Weeks Ago
Replies: 1
Views: 82
Posted By NCboatrx
Re: yanmar injection pump

This is a specialized job usually done at a fuel injection shop. They are the only ones in my experience who can calibrate and test an injection pump.

Stanley
Forum: Diesel 06-03-2014
Replies: 4
Views: 333
Posted By NCboatrx
Re: Single lever controls

This control is adjustable for different transmissions so you should not have any problems. They are widely used for Hurth/ ZF, PRM, Technodrive, Borg Warner Velvet Drive etc.
Forum: Diesel 06-02-2014
Replies: 4
Views: 333
Posted By NCboatrx
Re: Single lever controls

That particular single lever control has been available for the last 40 years. The reason that it has lasted in production for so long is that it just plain works.
It is easy to set up and you can...
Forum: Diesel 05-02-2014
Replies: 2
Views: 316
Posted By NCboatrx
Re: Volvo penta

Contact Dick Vosbury at Vosbury Marine in Annapolis MD. He is the go to guy for all the old Volvo's.
Forum: Diesel 04-04-2014
Replies: 46
Views: 2,046
Posted By NCboatrx
Re: Yanmar super vibration

Have you actually checked your propeller? What you are describing is a classic symptom with a worn folding or feathering propeller or a bent blade on a fixed propeller.
Forum: Diesel 11-04-2013
Replies: 5
Views: 520
Posted By NCboatrx
Re: MD7A or parts for sale

Yes, this does look like a MD7A.
Forum: Diesel 10-21-2013
Replies: 2
Views: 493
Posted By NCboatrx
Re: Volvo Penta MD6A Thermostat

Contact Dick Vosbury at Vosbury Marine in Annapolis MD. His email is vosburym@aol.com and he is the go to guy for these old Volvo's.
Forum: Diesel 08-14-2013
Replies: 15
Views: 1,128
Posted By NCboatrx
Re: Deisel Engine Day Tank.

Actually this is quite correct and most definately not nonsense. Pumps have a problem sucking up and if you take the time to check manufacturers specifications on almost all types of pumps, the...
Forum: Diesel 06-26-2013
Replies: 20
Views: 1,130
Posted By NCboatrx
Re: Universal m4-30 engine will not accelerate in reverse, OK in forward Hurth selec

It is possible that some wear in the propeller is stopping it from opening fully in one direction. Has the prop been greased recently?
Forum: Diesel 06-25-2013
Replies: 20
Views: 1,130
Posted By NCboatrx
Re: Universal m4-30 engine will not accelerate in reverse, OK in forward Hurth selec

If the engine revs up normally in neutral, the issue is in the drive line. The first thing to check is that the prop is not full of growth and that there is no line or fish net around it and the...
Forum: Diesel 06-03-2013
Replies: 14
Views: 1,925
Posted By NCboatrx
Re: Cummins 4B 3.3

Hello JRD22,
The Beta 60 is not an electronically governed engine. The only electronic part of this engine is the stop solenoid.
Stanley
Forum: Diesel 05-01-2013
Replies: 3
Views: 740
Posted By NCboatrx
Re: Universal 5432 Oil Pressure Sending unit

Be very careful! Having an oil switch and oil sender on one fitting with a T connector can lead to disaster. The fittings are too heavy and the vibration often causes the nipple between the block and...
Forum: Diesel 05-01-2013
Replies: 6
Views: 978
Posted By NCboatrx
Re: universal M4-30 engine fresh water pump

The V850 was made for Westerbeke and is an uprated version of the V800. You will find spares for the V800 at a Kubota engine dealer, not at a Kubota tractor dealer. You will find the list of Kubota...
Forum: Diesel 03-27-2013
Replies: 8
Views: 1,296
Posted By NCboatrx
Re: Volvo Penta MD7A started but shut off

Follow the instructions in your manual for bleeding the fuel system and then you will find that your engine works again. All the air that you introduced into the fuel system is now in the injection...
Forum: Diesel 03-25-2013
Replies: 1
Views: 689
Posted By NCboatrx
Re: Volvo Penta 2003 Transmission

The V stands for a V drive. You have the regular MS2 transmission.
Forum: Diesel 03-21-2013
Replies: 4
Views: 447
Posted By NCboatrx
Re: Sender units for Farymann

This engine only has a temp switch for a temperature alarm. Farymann never supplied a gauge.

There is no provision for an oil gauge as this engine is splash lubricated.
Forum: Diesel 03-07-2013
Replies: 5
Views: 688
Posted By NCboatrx
Re: Westerbeke W30/4-91 Idle Screw Assembly Needed, or engine for parts

eherlihy. Some Westerbeke engines are built on Mitsubishi diesels. In this case you are completely wrong and MARC is correct. This engine is a marinised British Leyland 1.5 liter diesel. Some parts...
Forum: Diesel 02-28-2013
Replies: 15
Views: 710
Posted By NCboatrx
Re: Paint

Interlux make a great paint called "bilgecote gray". This is a cheap solution and the paint is easy to apply and oil and grease resistant.
Forum: Diesel 11-13-2012
Replies: 5
Views: 597
Posted By NCboatrx
Re: Kubota rattle

This could be caused by the injector. I suggest that you have it checked.
Forum: Diesel 11-12-2012
Replies: 16
Views: 2,068
Posted By NCboatrx
Re: Question on Volvo MD6A problems

That is the Volvo MS2 transmission. The seal is easy to replace but you may find the surface that it runs on has some rust which is what damaged the seal in the first place.

Remove the screw at...
Forum: Diesel 10-31-2012
Replies: 16
Views: 2,068
Posted By NCboatrx
Re: Question on Volvo MD6A problems

That price for an injection pump is completely out of order. It is about half the price of a replacement new engine complete with heat exchanger cooling, transmission, panel, mounts etc.(also comes...
Forum: Diesel 10-24-2012
Replies: 1
Views: 400
Posted By NCboatrx
Re: BorgWarner series 500 Gearbox

Borg Warner stopped supporting this transmission years ago. They didn't make many.

You may be better off looking at a replacement transmission from another manufacturer.

Regards, Stanley
Forum: Diesel 07-25-2012
Replies: 9
Views: 945
Posted By NCboatrx
Re: Farymann Diesel A30M Fuel Lines

This is an easy job. The fuel supply lines have banjo fittings at the end and over the last 33 years the rubber hose has hardened up, hence your leaks. These are not high pressure lines.
1) Undo...
Forum: Diesel 07-19-2012
Replies: 2
Views: 669
Posted By NCboatrx
Re: Volvo penta 2003 sail drive in Annapolis

Contact Vosbury Marine. They are the Volvo dealers in Annapolis and Dick Vosbury knows these engines and saildrives better than anyone else.
Stanley
Showing results 1 to 25 of 54

 

All times are GMT -4. The time now is 07:51 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.