SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 15 of 15
Search took 0.03 seconds.
Search: Posts Made By: 34crealock
Forum: Pacific Seacraft 06-27-2014
Replies: 15
Views: 1,084
Posted By 34crealock
Re: PSC 37 staysail sheet rigging options?

Grant, it is the same on my 34, if I run the sheets out side the shroud then I can't go to windward without rubbing, if I run them inside and then ease the sheets they rub inside. I put plastic snap...
Forum: Pacific Seacraft 04-21-2014
Replies: 16
Views: 1,111
Posted By 34crealock
Re: Got the air bleed blues

I think if you have bled the high pressure fuel pump it will take care of the injectors. If you have been cranking the engine over with the raw water intake open you may have already got water in the...
Forum: General Discussion (sailing related) 03-07-2014
Replies: 68
Views: 2,543
Posted By 34crealock
Re: The compass ... old hat?

The compass is always part of my continuous cross check. It is most likely the most reliable tool on the boat. After a lightning strike takes out all the toys it is nice to know that DR( time and...
Forum: Pacific Seacraft 02-19-2014
Replies: 9
Views: 533
Posted By 34crealock
Re: Anybody have an engine monkey I could use?

Mine was on the hard also and having a below deck autopilot installed. The new bronze shoe for the rudder and associated hardware was $ 850. The labor was 3 and 1/2 hours which included dropping the...
Forum: Pacific Seacraft 02-18-2014
Replies: 9
Views: 533
Posted By 34crealock
Re: Anybody have an engine monkey I could use?

I had the same problem when I refit Coorie Doon 2 years ago. I bit the bullet and had the yard drop the rudder and we fitted new bearings/ seals including the big bronze one on the skeg. I am hoping...
Forum: Pacific Seacraft 02-04-2014
Replies: 3
Views: 371
Posted By 34crealock
Re: Cockpit Lazarette Repair

That's one I havn't heard of in a PSC. I had a similar bit of rot in a C&C years ago that started around the hinges and it had gotten a bit spongy. I dug out the spongy stuff near the hinges and back...
Forum: Pacific Seacraft 01-21-2014
Replies: 6
Views: 1,941
Posted By 34crealock
Re: Dodger frame

On Coorie Doon when I had a Bimini built we built it with more strength and frames on top for solar. To improve visibility at the helm we raised the Bim above the dodger and put zippers on the bim...
Forum: Learning to Sail 11-23-2013
Replies: 10
Views: 1,849
Posted By 34crealock
Re: Why use a topping lift

Once you get the main sail up, slack off the topping lift enough so you can mange the sail without pulling on the topping lift. When you sheet in the main sheet too tightly you will stress the...
Forum: Pacific Seacraft 11-05-2013
Replies: 22
Views: 1,750
Posted By 34crealock
Re: Midship Cleats...

Mine are just like Rain Dog/Ocean Girl . They seem well placed for springing on or off a dock or hip towing with small inflatables to 25 foot towboats and after 3 years I have not had them foul any...
Forum: Pacific Seacraft 10-26-2013
Replies: 11
Views: 1,190
Posted By 34crealock
Re: 3JH2E Cruising RPM

I normally cruise at about 5 and 1/2 knots, which equates to 2100 RPM with a 3 bladed max prop. The pitch is set so I can get 3250 RPM wide open for about 7 knots. There has been discussion on some...
Forum: Pacific Seacraft 09-15-2013
Replies: 5
Views: 634
Posted By 34crealock
Re: Has anyone raised the boom on a PSC 37'?

Once you start raising the boom it depends on how much mast you have up top that you are not already using. If you just angle the boom up without cutting the sail you will have sail shape problems. ...
Forum: Pacific Seacraft 09-13-2013
Replies: 5
Views: 634
Posted By 34crealock
Re: Has anyone raised the boom on a PSC 37'?

To add solar to the top of my new bimini (PSC 34)I had the main sail cut 10 inches off the foot tapered to 0 inches at th luff so that I could raise the angle of the boom with minimum sail loss....
Forum: Gear & Maintenance 08-30-2013
Replies: 16
Views: 1,251
Posted By 34crealock
Re: Plastic dinghy repairs

I tried marine silicone goop and it did not keep the water out for a week. I think when the plastic gets too brittle it is time to junk the dink. It seems when you fiberglass one bad spot another...
Forum: Pacific Seacraft 08-11-2013
Replies: 20
Views: 1,510
Posted By 34crealock
Re: Stow location for batteries on PSC 34

I added a house bat to the port locker just aft of the bat box. It is in it's own plastic box secured to the wooden bulkhead and wired directly to the 2 other house bats. I have a third system in...
Forum: General Discussion (sailing related) 06-17-2013
Replies: 8
Views: 438
Posted By 34crealock
Re: Out of the Dungeon and Back into the Light

Alan King, rest his soul ( sole) said, " anyone who owns their own home, deserves it". He may have been right, you can't sail a house but you can live on a boat.:)
Showing results 1 to 15 of 15

 

All times are GMT -4. The time now is 10:44 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.