SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: Sundayflyer32
Forum: Islander 08-21-2013
Replies: 4
Views: 422
Posted By Sundayflyer32
I28 - Gas Tank Info

I have a 1978 I28 still with the Atomic 4. This last weekend I replaced the main fuel shut off valve as the original was getting sticky and wouldn't always shut off.

I got a suitable replacement...
Forum: Islander 07-15-2013
Replies: 2
Views: 295
Posted By Sundayflyer32
Wanted - Rudder for I-28

I am looking for a rudder form my I-28 as the original rudder has had freeze/thaw damage form many years outside. I can try taking it off in the fall and finding a FG shop that could make me a new...
Forum: Atomic 4 07-15-2013
Replies: 4
Views: 766
Posted By Sundayflyer32
Re: A4 Clutch slipping

Did it operate correctly in the past or has it always done this? After I bought my Islander 28 a couple of years ago I discovered something similar with the boat. However I was not familiar with...
Forum: Islander 10-16-2012
Replies: 1
Views: 801
Posted By Sundayflyer32
I28 - Great Lakes PHRF Rating

I am looking for a current PHRF rating for the I28 on the Great Lakes. Internet research seems to be showing a 201 rating and would be interested if that rating is what should be used for a standard...
Forum: Atomic 4 09-25-2012
Replies: 4
Views: 823
Posted By Sundayflyer32
Atomis 4 Water Pump Greaser fitting

FYI all you A4 lovers, I was going to screw in the grease cap to lubricate the water pump when I thought I better check to see if there was grease in the cap.
When I unscrewed the cap, the whole...
Forum: Islander 08-28-2012
Replies: 1
Views: 448
Posted By Sundayflyer32
Re: strut bearing replacement for Ib30

Hi There: I had a marina replace my cutlass bearing on my I-28 this spring and they pulled the shaft as well. You will have to remove 2 set screws that should be holding the bearing in the strut...
Forum: Islander 07-29-2012
Replies: 3
Views: 540
Posted By Sundayflyer32
Re: I28 - Mosquito Protection for Main Hatch

Attn: Tranquility Base

I can't figure out how to attach photos so if you wish to contact me at

jill_drew@rogers.com

I will send you some pics of my screens.
Forum: Islander 07-16-2012
Replies: 3
Views: 540
Posted By Sundayflyer32
Re: I28 - Mosquito Protection for Main Hatch

Hi there Tom: I will take a few pics when at the boat this weekend and attempt to post when I get back. This approach would only work on the I28 as a friend with a I32 doesn't have the same amount...
Forum: Islander 07-16-2012
Replies: 3
Views: 540
Posted By Sundayflyer32
I28 - Mosquito Protection for Main Hatch

Just wanted to share that I built a nice mosquito protection hatch for my I-28. The companion way on my 28 has the main sliding hatch and inside below the runners for the hatch, are strips of teak...
Forum: Islander 06-28-2012
Replies: 7
Views: 1,647
Posted By Sundayflyer32
Re: Islander 28 Backstay Adjuster Preferences

Here is an update. I removed the fore stay and pulled the mast vertical and measured about 4.5 inch extension required. I bought new link plates and plan to use a back stay adjuster to take up the...
Forum: Islander 06-17-2012
Replies: 7
Views: 1,647
Posted By Sundayflyer32
Re: Islander 28 Backstay Adjuster Preferences

Hi Paul et all: Last year I bought a I-28 and have been doing a number of repairs. I still have to do the compression post as I ran out of time this spring. I noticed in these posts that there are...
Forum: Islander 10-14-2011
Replies: 44
Views: 4,315
Posted By Sundayflyer32
Thanks for the prompt response. I can see a...

Thanks for the prompt response. I can see a piece of ply across 2 stringers which I am assuming is the plywood to be replaced. How is the post attached to the bulkhead between the cabin and the...
Forum: Islander 10-14-2011
Replies: 3
Views: 1,198
Posted By Sundayflyer32
Cutlass Bearing Replacement - Advice

Thanks for the information and I will have a good look at it again in the spring. I am reluctant to remove the shaft, but will have a good look while it is on the hard. I suppose it might be a good...
Forum: Islander 10-13-2011
Replies: 3
Views: 1,198
Posted By Sundayflyer32
Islander 28 - Atomic 4 - Cutlass bearing

How much play if any is OK for a cutlass bearing? My old 1978 I28 has a "bit" of play now that it is out of the water for winter and was wondering about what is acceptable. I saw from other threads...
Forum: Islander 10-13-2011
Replies: 44
Views: 4,315
Posted By Sundayflyer32
I am a new owner of a 1978 Islander 28 and have a...

I am a new owner of a 1978 Islander 28 and have a compression post issue as well. The other threads indicate removing the existing post and replacing/shimming the bottom end to restore the correct...
Showing results 1 to 15 of 15

 

All times are GMT -4. The time now is 10:22 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.