SailNet Community - Search Results
Advanced Search
Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: pmt200
Forum: Cal   06-03-2012
Replies: 8
Views: 2,089
Posted By pmt200
Re: Atomic 4 cutting out in forward.

Hi All,
Once again,thanks for all the responses and suggestions. Believe it or not the culprit was the ignition coil which was new (3 hours of use). Yesterday, I replaced the coil and the spark...
Forum: Cal   05-31-2012
Replies: 8
Views: 2,089
Posted By pmt200
Re: Atomic 4 cutting out in forward.

Thank you all for the prompt replies and suggestions. Yes, I was experiencing the cutting out under load prior to replacing the carb. and new fuel filter/separator. I went at it again today by...
Forum: Cal   05-30-2012
Replies: 8
Views: 2,089
Posted By pmt200
Atomic 4 cutting out in forward.

Hi All,
I have a fresh water cooled A4, that up until now ran great. After sitting over the winter, The engine starts fine, idles well, runs fine under load in reverse, but cuts out after 30 seconds...
Forum: Cal   10-05-2010
Replies: 3
Views: 708
Posted By pmt200
re Cal 34 engine controls

Wow!
Thanks to all for the speedy replies.
Dieselboy....Thanks for the offer of photos, but I believe it or not, today I managed to pick up the missing parts for the controls from a great marine...
Forum: Cal   10-03-2010
Replies: 3
Views: 708
Posted By pmt200
Cal 34 engine controls

Hi all,
I have an old Cal 34 with tiller steering and am trying to re-assemble the two lever Morse engine controls which were removed by a previous owner. I think there is a part or parts missing...
Forum: Gear & Maintenance   06-26-2010
Replies: 22
Views: 9,451
Posted By pmt200
TackTick T033 "35' " comment

I am thinking of installing the T033 system and spoke with a TackTick rep in the US called Don at 203 453 3090 and asked about the significance of the " boats up to 35' " statement re the T033. Don...
Forum: Cal   05-23-2010
Replies: 10
Views: 2,661
Posted By pmt200
Re Cal 2-29:Diameter of Running Rigging?

Hi Arch,
I think you will find that 3/8" is sufficient for a cruising sailboat that is not a regular racer. You should visit the web site of Mauri Pro Sailing and go to Rigging and click on Halyard...
Forum: Cal   08-27-2009
Replies: 0
Views: 755
Posted By pmt200
Cal 34 Tiller post cap

Hello,
Does anyone know where I can obtain a replacement cap and tiller bracket for my 1969 Cal 34? The tiller post is 2 7/8" diameter.

Peter Mc T
Forum: Gear & Maintenance   08-27-2009
Replies: 21
Views: 3,538
Posted By pmt200
Sara, I have a 1969 cal 34 with tiller steering...

Sara,
I have a 1969 cal 34 with tiller steering which is out of the water for a major refit. I just removed the tiller and there are no bearings inside the shaft, although there is a grease nipple...
Forum: Cal   11-28-2007
Replies: 0
Views: 2,644
Posted By pmt200
Cal 34 Tiller

Hi All,
I would like to replace the tiller on my 1969 Cal 34 which I am not sure is an original Cal 34 tiller as it looks quite flimsy. Does anyone have the dimensions for an original Cal 34 tiller...
Showing results 1 to 10 of 10

 
 
For the best viewing experience please update your browser to Google Chrome