SailNet Community - Search Results

   Search Sailnet:

 forums  store  

Quick Menu
Boat Reviews  
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Hatches and Portlights
Interior And Galley
Marine Electronics
Other Items
Plumbing and Pumps
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here

Go Back   SailNet Community > Search Forums
 Not a Member? 

Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: pmt200
Forum: Cal 06-04-2012
Replies: 8
Views: 1,879
Posted By pmt200
Re: Atomic 4 cutting out in forward.

Hi All,
Once again,thanks for all the responses and suggestions. Believe it or not the culprit was the ignition coil which was new (3 hours of use). Yesterday, I replaced the coil and the spark...
Forum: Cal 05-31-2012
Replies: 8
Views: 1,879
Posted By pmt200
Re: Atomic 4 cutting out in forward.

Thank you all for the prompt replies and suggestions. Yes, I was experiencing the cutting out under load prior to replacing the carb. and new fuel filter/separator. I went at it again today by...
Forum: Cal 05-30-2012
Replies: 8
Views: 1,879
Posted By pmt200
Atomic 4 cutting out in forward.

Hi All,
I have a fresh water cooled A4, that up until now ran great. After sitting over the winter, The engine starts fine, idles well, runs fine under load in reverse, but cuts out after 30 seconds...
Forum: Cal 10-05-2010
Replies: 3
Views: 664
Posted By pmt200
re Cal 34 engine controls

Thanks to all for the speedy replies.
Dieselboy....Thanks for the offer of photos, but I believe it or not, today I managed to pick up the missing parts for the controls from a great marine...
Forum: Cal 10-03-2010
Replies: 3
Views: 664
Posted By pmt200
Cal 34 engine controls

Hi all,
I have an old Cal 34 with tiller steering and am trying to re-assemble the two lever Morse engine controls which were removed by a previous owner. I think there is a part or parts missing...
Forum: Gear & Maintenance 06-26-2010
Replies: 22
Views: 9,294
Posted By pmt200
TackTick T033 "35' " comment

I am thinking of installing the T033 system and spoke with a TackTick rep in the US called Don at 203 453 3090 and asked about the significance of the " boats up to 35' " statement re the T033. Don...
Forum: Cal 05-23-2010
Replies: 10
Views: 2,398
Posted By pmt200
Re Cal 2-29:Diameter of Running Rigging?

Hi Arch,
I think you will find that 3/8" is sufficient for a cruising sailboat that is not a regular racer. You should visit the web site of Mauri Pro Sailing and go to Rigging and click on Halyard...
Forum: Cal 08-27-2009
Replies: 0
Views: 697
Posted By pmt200
Cal 34 Tiller post cap

Does anyone know where I can obtain a replacement cap and tiller bracket for my 1969 Cal 34? The tiller post is 2 7/8" diameter.

Peter Mc T
Forum: Gear & Maintenance 08-27-2009
Replies: 21
Views: 3,294
Posted By pmt200
Sara, I have a 1969 cal 34 with tiller steering...

I have a 1969 cal 34 with tiller steering which is out of the water for a major refit. I just removed the tiller and there are no bearings inside the shaft, although there is a grease nipple...
Forum: Cal 11-29-2007
Replies: 0
Views: 2,589
Posted By pmt200
Cal 34 Tiller

Hi All,
I would like to replace the tiller on my 1969 Cal 34 which I am not sure is an original Cal 34 tiller as it looks quite flimsy. Does anyone have the dimensions for an original Cal 34 tiller...
Showing results 1 to 10 of 10


All times are GMT -4. The time now is 09:03 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) LLC 2000-2012

The store is owned and operated by a company independent of the forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.