SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Chat  
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 8 of 8
Search took 0.01 seconds.
Search: Posts Made By: arf145
Forum: Diesel 02-01-2015
Replies: 22
Views: 3,305
Posted By bigdogandy
Re: Yanmar 3GM oil line failure

I just had the same problem - the oil feed line rusted through at the banjo fitting behind the fuel lift pump. It only took a few minutes to pump all the oil out of the engine and into the sump under...
Forum: Beneteau 01-21-2014
Replies: 4
Views: 608
Posted By svHyLyte
Re: Beneteau 343 2006 Salt water intake

Tom--

Your through hulls are likely fine. (To satisfy yourself, however, polish a patch of your through hull will some light sand paper. If the underlying material is yellow/gold in color, your...
Forum: Diesel 11-17-2013
Replies: 265
Views: 62,492
Posted By Jacques-Andre
Re: Perkins 4.108M DIY Rebuild -- A Narrative

Don't you all worry.

He's fine, just has other things in his life than keeping us happy here! Its quite good that he managed to get that much time to devote to this project without someone...
Forum: Electronics 10-06-2013
Replies: 4
Views: 410
Posted By svinshallah
Re: Seatalk Cross Interference

First thing is to check ALL of the grounds associated with the system. Every one. Seatalk uses a common ground for -12V and the data ground. Bad grounds create noise on the Seatalk bus.
Forum: Chesapeake Bay 07-20-2013
Replies: 5
Views: 542
Posted By Gladrags1
Re: Knapps Narrows

It would be tight, especially around the R4 on the western side. They have installed a new green buoy to help - you need to stay real close to the R4 and turn sharply afterwards. It can be done with...
Forum: Gear & Maintenance 07-02-2013
Replies: 11
Views: 804
Posted By chef2sail
Re: Refill Propane?

Ace hardware is where we go. Many have refill stations . If you are near Deale which I think you are try Amerigas, Ferrelgas, ask in your marina. Make sure you have a modern tank with pressure...
Forum: Gear & Maintenance 07-01-2013
Replies: 4
Views: 414
Posted By PAULCR1
Rounded bolts and/or nuts

I don't know if it's o.k. to mention a specific product or not but I'll try. I had a 17mm bolt that ran into the rear of my Universal engine. The bolt held a bracket that had rusted through. First...
Forum: Diesel 11-25-2011
Replies: 22
Views: 3,305
Posted By jrd22
Yanmar 3GM oil line failure

My brother and I installed a new 3GM in the early 90's and apart from normal maintenance it's been trouble free and still looks almost new. A few weeks ago it was run while in the slip for about 20...
Showing results 1 to 8 of 8

 

All times are GMT -4. The time now is 10:44 AM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.