SailNet Community - Search Results

   Search Sailnet:

 forums  store  


Quick Menu
Forums           
Articles          
Galleries        
Boat Reviews  
Classifieds     
Search SailNet 
Boat Search (new)

Shop the
SailNet Store
Anchor Locker
Boatbuilding & Repair
Charts
Clothing
Electrical
Electronics
Engine
Hatches and Portlights
Interior And Galley
Maintenance
Marine Electronics
Navigation
Other Items
Plumbing and Pumps
Rigging
Safety
Sailing Hardware
Trailer & Watersports
Clearance Items

Advertise Here






Go Back   SailNet Community > Search Forums
 Not a Member? 


Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: Mandofish
Forum: Seamanship & Navigation 04-15-2011
Replies: 19
Views: 4,381
Posted By Mandofish
I don't think i would have the tearing thru hands...

I don't think i would have the tearing thru hands problem if i cleat off the rode, then walk the bitter end to the bow, cleat, then release stern cleat right?

I Appreciate your directions, its...
Forum: Seamanship & Navigation 04-15-2011
Replies: 19
Views: 4,381
Posted By Mandofish
Stern Anchoring Question

So, I've read a lot about setting an anchor and all the various techniques folks use. I have set an anchor from the bow of my 26' sailboat several times now using under power using the typical...
Forum: Gear & Maintenance 08-27-2009
Replies: 12
Views: 1,533
Posted By Mandofish
I like the idea of manufacturing a drain slot in...

I like the idea of manufacturing a drain slot in the stanchion base...but I don't own a grinder. Any way to do this without big expensive tools?
Forum: Gear & Maintenance 08-26-2009
Replies: 12
Views: 1,533
Posted By Mandofish
The bases have been removed already and yes,...

The bases have been removed already and yes, there was considerable core rot around the old holes, which I removed and then filled with epoxy. (following the excellent recommendations at Maine...
Forum: Gear & Maintenance 08-26-2009
Replies: 12
Views: 1,533
Posted By Mandofish
Drilling a rain hole in the base is not really...

Drilling a rain hole in the base is not really possible due to the curved shape of the base, and the fact that the drain hole would still be at least 1/2 inch higher than deck level which would still...
Forum: Gear & Maintenance 08-26-2009
Replies: 12
Views: 1,533
Posted By Mandofish
Filling a Stanchion?

I am in the process of re-bedding my stanchion bases and adding backing plates. Upon removing the stanchion bases, I notice lots of rot and gunk buildup under the bases. I believe this is due to...
Forum: Gear & Maintenance 08-18-2009
Replies: 2
Views: 468
Posted By Mandofish
Bill, I get my outboard serviced at Specialty...

Bill, I get my outboard serviced at Specialty Marine in Oxnard. While I've only had regular servicing performed on a 5 hp Tohatsu, no major repairs, the place seemed very professional and...
Forum: Gear & Maintenance 04-03-2009
Replies: 34
Views: 2,231
Posted By Mandofish
Its not the mast base blocks that are the issue,...

Its not the mast base blocks that are the issue, those are already installed at the mast base. Its the deck organizer (actually a double cheek block) that needs to be affixed to the cabin top. If I...
Forum: Gear & Maintenance 04-03-2009
Replies: 34
Views: 2,231
Posted By Mandofish
Need to run lines (halyard, reefs) back to the...

Need to run lines (halyard, reefs) back to the cockpit but he cabin top on my Columbia Mk26 is too rounded ("bubble" style cabin top) to mount the hardware directly to the cabin top surface!
Forum: Gear & Maintenance 04-03-2009
Replies: 34
Views: 2,231
Posted By Mandofish
Ok..this leads me to a second question...what if...

Ok..this leads me to a second question...what if I were to use an aluminum plate as a BASE plate for some hardware on the cabin top, which would be secured with stainless bolts...would this be a bad...
Forum: Gear & Maintenance 04-03-2009
Replies: 34
Views: 2,231
Posted By Mandofish
Thanks, I will try the fiberglass layup technique!

Thanks, I will try the fiberglass layup technique!
Forum: Gear & Maintenance 04-03-2009
Replies: 34
Views: 2,231
Posted By Mandofish
Would thoroughly saturating the oak with epoxy...

Would thoroughly saturating the oak with epoxy and/or encasing it in fiberglass solve these issues? (splitting, cracking, warping?) I am having a hard time finding marine plywood.
Forum: Gear & Maintenance 04-03-2009
Replies: 34
Views: 2,231
Posted By Mandofish
Oak for backing plates?

Is there any reason not to use oak board for backing plates for deck hardware? I know aluminum, stainless steel, fiberglass, and marine plywood are typically used, but why not oak? I would of course...
Forum: General Discussion (sailing related) 12-03-2008
Replies: 0
Views: 543
Posted By Mandofish
Running lines aft Columbia 26?

Does anyone out there have a Columbia 26 MKII with lines led aft to the cockpit? I have done a lot of web searching and reading on this forum about leading lines aft and I think I understand whats...
Forum: Introduce Yourself 12-03-2008
Replies: 3
Views: 339
Posted By Mandofish
Hello Sailnet!

Hello All! Just introducing myself on this wonderful forum. Recently purchased a 1970 Columbia 26 MKII. Planning on doing some retrofitting and am new to sailing "larger" boats (sailed hobies,...
Showing results 1 to 15 of 15

 

All times are GMT -4. The time now is 04:05 PM.

Add to My Yahoo!         
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
SEO by vBSEO 3.6.1
(c) Marine.com LLC 2000-2012

The SailNet.com store is owned and operated by a company independent of the SailNet.com forum. You are now leaving the SailNet forum. Click OK to continue or Cancel to return to the SailNet forum.