Teak Deck Thickness - SailNet Community
LinkBack Thread Tools
post #1 of 3 Old 11-09-2005 Thread Starter
Join Date: Nov 2005
Posts: 29
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Teak Deck Thickness

I need to decide on the teak thickness of the cockpit deck flooring in my 36'' steel cutter. I realize that thickness will increase the cost, but I want the project to be done right.

I believe the deck should be at least 3/8" thick and currently I am considering 1/2". But since I don''t have any experience with teak decking I wanted to get some feedback from others with experience.

Thanks in advance for your input.
Mithril is offline  
Sponsored Links
post #2 of 3 Old 11-09-2005
Senior Member
paulk's Avatar
Join Date: Jun 2000
Location: CT/ Long Island Sound
Posts: 3,546
Thanks: 4
Thanked 91 Times in 90 Posts
Rep Power: 21
Teak Deck Thickness

The thickness of a teak deck used to be determined by how big the screws holding it down were, plus enough for the bung to hide the screwhead. If the material was too thin, the screws wouldn''t hold it down properly, or the bungs would tend to pop out. This used to mean decks an inch or so thick. Modern glues have made it possible to glue teak down and NOT screw it at all. This is a good thing, since the screwholes eventually start to leak and then cause problems in the substrate that the teak is screwed to. If you''re just gluing it down, figure it might wear down every year or so, especially in a high traffic area like the cockpit. Half-inch stock might give you about 15 years of use. (That''s a guess - you may want to look at various teak decks of different ages to see how much they thin out in sun/rain/wind conditions where you are.) That''s why people often put teak grating on the cockpit sole, without gluing it down. It''s easier to replace, cheaper, and lighter.
paulk is online now  
post #3 of 3 Old 11-09-2005 Thread Starter
Join Date: Nov 2005
Posts: 29
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Teak Deck Thickness

Thanks Paul...

My plan is to NOT use screws of any kind, even if that means I have to reapply adhesive again later. I just spent $8,000 cutting out and welding in a new cockpit sole because of rusting caused by among other things screw holes.

I''ve heard that some yards and builders are using some kind of "vacuum" application for teak decking. Does anyone know anything about this process?
Mithril is offline  

Quick Reply

By choosing to post the reply above you agree to the rules you agreed to when joining Sailnet.
Click Here to view those rules.

Register Now

In order to be able to post messages on the SailNet Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
Please note: After entering 3 characters a list of Usernames already in use will appear and the list will disappear once a valid Username is entered.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page

Similar Threads
Thread Thread Starter Forum Replies Last Post
What thickness Marine ply for Cal 25 deck? Quercus Cal 0 07-01-2017 01:47 PM
Deck thickness on PSC 34 at windlass mount surface mondofromredondo Pacific Seacraft 4 06-04-2015 09:52 PM
Lexan thickness for deck hatch Alden68 Gear & Maintenance 38 03-13-2008 06:05 PM
portlight bulkhead thickness... Rockter Gear & Maintenance 7 08-26-2007 09:24 PM
fiberglass thickness SeanC. Gear & Maintenance 1 01-29-2006 12:29 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome