SailNet Community banner
  • SailNet is a forum community dedicated to Sailing enthusiasts. Come join the discussion about sailing, modifications, classifieds, troubleshooting, repairs, reviews, maintenance, and more!

mast bend problem

3K views 17 replies 11 participants last post by  Sanduskysailor 
#1 ·
mast is up and straight side to side.
i'm unable to get the mast straight fore to aft above the spreaders.
it is bent forward the amount it seems like it should be aft.
i have roller furling which is hanging limp, not tight enough on the stay with the halyard tight.
yet there is no more adjustment on the split backstay turnbuckle.
i'm thinking of re stepping the mast
although since the step has only one bolthole i'm not sure if it would make a difference.
i'm also considering shortening the lowers on the backstay.
this is the first time i've raised the mast on this boat but everything seemed okay when i took it down.
any thoughts?
 
#2 ·
Just a "few" questions....
size of boat?
what make?
type of rig?
Compression post rotted?
are the aft chain plates pulling out?
Is the back stay proper on the mast head?
is the mast head broken. is the mast back wards? ( it has happened)
Are the lower shrouds pulling the mast fwd at the spreader height?
 
#3 ·
5.5 mirage
masthead rig
all fittings and rigging in good condition.
spreaders all level and raked aft correctly.
it just appears like the backstay is unable to pull the masthead back enough.
when i pull the split stays together the masthead does move aft.
 
#4 · (Edited)
If everything was fine before you took the mast down, then what could have changed when you put it back up? Did the forestay turnbuckle get wound out making the forestay too long? Is the backstay rigged the same as it was before? How much shroud tension do you have? If you have aft swept spreaders then shroud tension will induce bend and tighten your forestay. You say you are considering shortening the lowers...are they hanging slack? Do the uppers and lowers fasten to separate chain plates? If so, are you sure you haven't got them reversed?

It is a pretty tough thing to diagnose based on the info you provide, but you say everything "seemed" ok when you took it down. Is this boat new to you? Had you ever sailed the boat prior to taking it down?

Do you have any pics of the rig?
 
#6 ·
Firstly, your rigg seems to be inverted. Not good for sailing. Fix it before you do anything else.

Secondly, what could be the origin of this and how to fix it? It is of course difficult to say without an inspection, much will be speculation.

Seems to be a traditional masthead, with forestay, backstay, right angled spreaders and forward and aft lowers. Mast top is however now pointing forward, but was OK before mast was unstepped. (?).

First guess would be that the lowers are not of the same length, and that the aft ones now are forward and the forward ones are aft (the forward ones is then slightly shorter than the aft ones). This forces the mast to bend somewhat back at the spreaders, leaving the mast top to go forward (due to the weight of the furler).
A small variation of this guess is that the aft lowers are too tight.
These guesses doesn't fully explain your issues with the backstay, but a bent mast is shorter than an unbent which could explain that part.

Not really sure how the backstay arrangement looks like. It is quite important that adequate tension can be applied, at a masthead this is more or less the only trimming point.

Good Luck

/J
 
#9 · (Edited)
Here ya go ... probably the most comprehensive rig tuning guide available on the web: http://www.riggingandsails.com/pdf/selden-tuning.pdf

Do pay attention to the proper amount of mast 'prebend' as all sailmakers 'depend' on such to be present as this will greatly affect the shape and performance of your mainsail; correct forestay tension affecting the proper shape of the headsail.

The understanding when using such 'rig guides' is that the boat will be set up tensionwise for the typical 12-15kts of windstrength. A set up for 12-15kt. windstrength is the 'plain vanilla' starting point.
If you are seriously racing this boat then the boat should be set up 'tighter' for both higher and lower windstrengths ... but the wire should not exceed 30% when full loaded and the boat over (to about 45° heel angle) as over this value will lead to premature rig failure. For serious racing tensions you before racing (during trials and prelim. set-ups) attach a tension meter to the rig while sailing at its maximum and then then make tension corrections back at the dock, etc. Sail SHAPE is dependent on proper rig tension ... and mast 'pre-bend'.
 
#12 ·
thanks for the insights.
upon inspection today i've noticed several things that may or may not be of relevance.
the headstay tack has two holes.
i've connected the stay to the forward hole.
the upper shroud on port spreader is running through aft while to starboard is forward.
the spreaders are square athwartship not raked aft as previously mentioned.
the boat is new to us and i've never rigged it before although i have rigged many trailer sailer before.
it is on the trailer and is level fore and aft as well as athwartship.
the former owner didn't use the boat much and can't be contacted.
the boat is equipped with a split backstay.
i'm thinking of re stepping the mast and trying to slip it a bit further forward.
i will try to post some photos but i'm not very good at that sort of thing.
 
#17 · (Edited)
It is a good idea to un-step the mast. As said earlier, an inverted mast is dangerous to use.

When doing so, check
- so the two sides are identical (or mirrored). Probably not very ctitical, but good to have.
- the lengths of the lowers (aft and forward).

When stepping the mast, at the initial stage do not apply high tension to the aft lowers. If there is any bend in the mast, the bend in itself should point forward, mast top aft (opposite to what you have today). A masthead mast should usually not have much bend, if any at all.

It is quite important to follow a scheme when stepping the mast, and applying tension to all stays. The Selden instruction, mentioned above, probably has such a scheme (read ...). Apply tension in steps, check mast for each round.

/J
 
#18 ·
I think you gave us a clue when you said forestay had 2 holes at deck. The condition you describe with the mast bending forward at the shrouds and is still loose is caused by a forestay that is too short. Put the fitting in the aft hole and see if that works. Also, was there a toggle at the deck fitting that is missing?
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top